MAX933 Maxim, MAX933 Datasheet
MAX933
Available stocks
Related parts for MAX933
MAX933 Summary of contents
Page 1
... MAX931-MAX934 minimize parasitic feedback, which makes them easier to use. The single MAX931 and dual MAX932/MAX933 provide a unique and simple method for adding hysteresis without feedback and complicated equations, using the HYST pin and two resistors ...
Page 2
... A MAX933, HYST = REF C/E temp. ranges T = +25°C A MAX934 C/E temp. ranges V = 2.5V CM IN+ = IN- = 2.5V, C/E temp. ranges MAX931, MAX932, MAX933 V- to (V+ – 1.3V 2.5V to 11V 100Hz to 100kHz MAX931, MAX932, MAX933 Overdrive = 10mV T = +25°C, 100pF load A Overdrive = 100mV = +70°C) A MIN TYP MAX UNITS 2 2.5 3 ...
Page 3
... A MAX932, HYST = REF C/E temp. ranges IN+ = (IN- + 100mV +25°C A MAX933, HYST = REF C/E temp. ranges T = +25°C A MAX934 C/E temp. ranges V = 1.5V CM IN+ = IN- = 1.5V, C/E temp. ranges MAX931, MAX932, MAX933 MIN TYP MAX UNITS V+ – 0 0.4 V GND + 0.4 1.158 1.182 1.206 V 1.147 1.217 15 25 µ µ ...
Page 4
... REFERENCE Reference Voltage Source Current Sink Current Voltage Noise 4 _______________________________________________________________________________________ , unless otherwise noted.) MAX CONDITIONS V- to (V+ – 1.3V 2.5V to 11V 100Hz to 100kHz MAX931, MAX932, MAX933 Overdrive = 10mV T = +25°C, 100pF load A Overdrive = 100mV C/E temp. ranges 10mA OUT MAX932, MAX933 C/E temp. ranges 0.8mA ...
Page 5
... TEMPERATURE 1.22 1.21 EXTENDED TEMP. RANGE 1.20 COMMERCIAL 1.19 TEMP. RANGE 1.18 1.17 1.16 1.15 1.14 -60 -40 - 100 120 TEMPERATURE ( C) MAX933 SUPPLY CURRENT vs. TEMPERATURE 5.0 IN+ = IN- +100mV 4 3.5 3 2.0 -60 - 100 TEMPERATURE ( C) _______________________________________________________________________________________ Ultra Low-Power, Low-Cost Comparators with 2% Reference OUTPUT VOLTAGE HIGH vs. LOAD CURRENT 5 ...
Page 6
Ultra Low-Power, Low-Cost Comparators with 2% Reference ____________________________Typical Operating Characteristics (continued) ( GND +25°C, unless otherwise noted.) A HYSTERESIS CONTROL 80 60 OUTPUT HIGH CHANGE -20 -40 OUTPUT LOW -60 ...
Page 7
... Descriptions PIN MAX931 MAX932 MAX933 1 – – – – – – – – – 4 – – – – – – PIN NAME MAX934 1 OUTB 2 OUTA INA- 5 INA+ 6 INB- 7 INB+ ...
Page 8
... Operating the MAX931 and MAX934 at ±5V provides TTL/CMOS compatibility when monitoring bipolar input signals. TTL compatibility for the MAX932 and MAX933 is achieved by operation from a single +5V supply. The guaranteed minimum operating voltage is 2.5V (or ±1.25V). As the total supply voltage is reduced below 2 ...
Page 9
... The negative supply does not affect the output swing, and can range from 0V to -5V ±10%. The MAX932 and MAX933 do not have a GND pin, and their outputs swing from V+ to V-. Connect V- to ground and +5V supply to achieve TTL compatibility. ...
Page 10
... (mV) HB When hysteresis is obtained in this manner for the MAX932/MAX933, the same hysteresis applies to both comparators. Hysteresis (MAX934) Hysteresis can be set with two resistors using positive feedback, as shown in Figure 4. This circuit generally draws more current than the circuits using the HYST pin on the MAX931/MAX932/MAX933, and the high feedback impedance slows hysteresis ...
Page 11
... For example: 2MΩ x 10µF x 4.6 = 92sec. The actual time will vary with both the leakage current of the capacitor and the voltage applied to the circuit. The MAX933 is ideal for making window detectors (undervoltage/overvoltage detectors). The schematic is shown in Figure 6, with component values selected for an 4 ...
Page 12
Ultra Low-Power, Low-Cost Comparators with 2% Reference 100nA for the thresholds to be accurate. R1 values up to about 10MΩ can be used, but values in the 100kΩ to 1MΩ range are usually easier to deal with. In this example, ...
Page 13
V+ MAX934 10k INA+ V INA INA- 10k INB+ V INB INB- 10k INC+ V INC INC- 10k IND+ V IND OUTD IND- V- GND -5V Figure 8. Level Shifter: ±5V Input to CMOS Output ______________________________________________________________________________________ Ultra Low-Power, Low-Cost ...
Page 14
... MAX934EPE REF MAX934ESE HYST For similar devices guaranteed over the military temp. range, see the MAX921-MAX924 data sheet. The MAX931, MAX933, and MAX934 are pin-compatible with the 1% accurate MAX921, MAX923, and MAX924, respectively. The MAX932 and MAX922 are not pin-compatible. OUTB ...
Page 15
Information ______________________________________________________________________________________ Ultra Low-Power, Low-Cost Comparators with 2% Reference 15 ...
Page 16
... Comparators with 2% Reference __________________________________________Package Information (continued) Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © ...