MAX4532 Maxim, MAX4532 Datasheet
MAX4532
Available stocks
Related parts for MAX4532
MAX4532 Summary of contents
Page 1
... The MAX4530/MAX4531/MAX4532 are low-voltage, CMOS analog ICs configured as an 8-channel multi- plexer (mux) (MAX4530), two 4-channel muxes (MAX4531), and three single-pole/double-throw switches (MAX4532). These devices are pin compatible with the industry-standard 74HC4351/74HC4352/ 74HC4353. All devices have two complementary switch-enable inputs and address latching. ...
Page 2
... COM A MAX4531 4.5V, ± NO MAX4532 V+ = 5.5V -5. +25° ±4.5V, COM MAX4530 5.5V -5.5V MAX4531 T = +25°C MAX4531/ A MAX4532 +70° 0.8V unless EN_L A MIN MAX MIN TYP MAX (Note 100 MIN MAX ...
Page 3
Low-Voltage, CMOS Analog Multiplexers/Switches with Enable Inputs and Address Latching ELECTRICAL CHARACTERISTICS—Dual Supplies (continued) (V+ = +5V ±10 -5V ±10%, GND = 0, V otherwise noted.) PARAMETER SYMBOL DIGITAL LOGIC INPUT ADD_H EN_H Logic High ...
Page 4
... MAX4530 V = 4.5V, 1V; COM 1V, 4.5V MAX4531 5.5V MAX4532 MAX4530 T A MAX4531 T MAX4531/ A MAX4532 0.8V unless EN_L A MIN MAX MIN TYP MAX (Note 2) = +25°C 0.025 = +25° +25° +25° +25° ...
Page 5
Low-Voltage, CMOS Analog Multiplexers/Switches with Enable Inputs and Address Latching ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued) (V+ = +5V ±10 GND = 0, V otherwise noted.) PARAMETER SYMBOL DIGITAL LOGIC INPUT V , ADD_H Logic-High Threshold V , ...
Page 6
... Select to Latch Enable) Hold Time, Latch Enable Channel Select Pulse Width, Latch Enable t MPW Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: Guaranteed by design. Note 4: ∆ (max (min). ON ...
Page 7
Low-Voltage, CMOS Analog Multiplexers/Switches with Enable Inputs and Address Latching __________________________________________Typical Operating Characteristics (T = +25°C, unless otherwise noted.) A ON-RESISTANCE vs. V COM (DUAL SUPPLIES) 100 90 V± = ±2. V± = ± V± = ...
Page 8
... NO_, NC_, and COM_ pins are identical and interchangeable. Either may be considered as an input or output; signals pass equally well in both directions. 8 _______________________________________________________________________________________ NAME MAX4532 — NO0–NO7 Analog Switch Inputs 0–7 — NO0B–NO3B Analog Switch “B” Inputs 0–3 ...
Page 9
... The V+ and V- sup- plies need not be symmetrical, but their sum cannot exceed the +13V absolute maximum rating. The MAX4530/MAX4531/MAX4532 operate from a sin- gle supply between +2V and +12V when V- is connect GND. All of the bipolar precautions must be observed ...
Page 10
... MAX4530 V+ EN2 EN1 GND ADD_ ADDA NO1_, NO2_ ADDB 50Ω MAX4531 V+ EN2 EN1 GND ADD_ ADD_ 50Ω MAX4532 V+ EN2 EN1 GND Figure 1. Address Transition Time 10 ______________________________________________________________________________________ +3V NO0 V ADD_ NO7 -3V COM V OUT 300Ω 35pF V OUT V- V- +3V NO0 V ...
Page 11
... NO1_, N02_, NO3_ ADDB MAX4531 V EN1 EN1 V+ EN2 50Ω GND ADD_ MAX4532 V EN1 EN1 V+ EN2 GND 50Ω FOR SINGLE-SUPPLY OPERATION. REPEAT TEST FOR EACH SECTION. REPEAT TEST FOR EN2, WITH PULSE INVERTED AND EN1 CONNECTED TO GND. Figure 2. Enable Switching Time ______________________________________________________________________________________ ...
Page 12
... LE V+ ADD_ ADDA NO0_–NO3_ ADDB 50Ω MAX4531 V+ EN2 EN1 GND ADD_ NO_, NC_ ADD_ 50Ω MAX4532 V+ EN2 EN1 GND FOR SINGLE-SUPPLY OPERATION. REPEAT TEST FOR EACH SECTION. Figure 3. Break-Before-Make Interval 12 ______________________________________________________________________________________ +3V COM V OUT 300Ω 35pF ...
Page 13
... OFF ISOLATION IS MEASURED BETWEEN COM_ AND OFF NO_ TERMINAL ON EACH SWITCH. ON LOSS IS MEASURED BETWEEN COM_ AND ON TERMINAL ON EACH SWITCH. CROSSTALK (MAX4531/MAX4532 IS MEASURED FROM ONE CHANNEL ( ALL OTHER CHANNELS. SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED. Figure 5. Off Isolation, On Loss, and Crosstalk ...
Page 14
... MAX4531 50Ω EN1 GND V+ EN2 V+ V ADD_ ADD_ 50Ω MAX4532 LE 50Ω EN1 GND FOR SINGLE-SUPPLY OPERATION. REPEAT TEST FOR EACH SECTION. Figure 7. Setup and Hold Times, Minimum LE Width 14 ______________________________________________________________________________________ +3V NO1–NO7 NO0 COM V OUT 300Ω ...
Page 15
... COMB–NO1B COMA–NO2A, 0 COM–NO6 COMB–NO2B COMA–NO3A, 1 COM–NO7 COMB–NO3B ON SWITCHES MAX4531 MAX4532 Last address All switches open All switches open COMA–NCA, COMB–NCB, COMC–NCC COMA–NOA, COMB–NCB, COMC–NCC COMA–NCA, COMB–NOB, COMC– ...
Page 16
... V- GND LE ADDA 0.053" (1.35mm ARE FOR MAX4532 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...