MAX4536 Maxim, MAX4536 Datasheet
MAX4536
Available stocks
Related parts for MAX4536
MAX4536 Summary of contents
Page 1
... The MAX4536/MAX4537/MAX4538 are quad, low-voltage, single-pole/single-throw (SPST) analog switches with a common enable pin. They are pin compatible with the industry-standard 74HC4316. The MAX4536 has four normally open (NO) switches, and the MAX4537 has four normally closed (NC) switches. The MAX4538 has two NO switches and two NC switches. ...
Page 2
... Note 2: All leads are soldered or welded to PC boards. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS— ...
Page 3
SPST Analog Switches with Enable ELECTRICAL CHARACTERISTICS—±5V Dual Supplies (continued) (V+ = 4.5V to 5.5V -4.5V to -5.5V, V values are +25°C.) A PARAMETER SWITCH DYNAMIC CHARACTERISTICS Turn-On Time Turn-Off Time Break-Before-Make Time Delay (MAX4538 ...
Page 4
Quad, Low-Voltage, SPST Analog Switches with Enable ELECTRICAL CHARACTERISTICS—+5V Single Supply (V+ = 4.5V to 5.5V 0V 2.4V, V INH values are +25°C.) A PARAMETER SYMBOL ANALOG SWITCH V Analog Signal Range V ...
Page 5
... Note 5: ∆R = ∆R - ∆R ON ON(MAX) ON(MIN) Note 6: Resistance flatness is defined as the difference between the maximum and the minimum value of on-resistance as measured over the specified analog-signal range. Note 7: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation +25°C. A ...
Page 6
Quad, Low-Voltage, SPST Analog Switches with Enable __________________________________________Typical Operating Characteristics (V+ = +5V -5V GND = 0V +25°C, unless otherwise noted.) A ON-RESISTANCE vs. V COM (DUAL SUPPLIES) 200 180 160 V± = ±1.5V 140 120 ...
Page 7
... Negative Analog Supply-Voltage Input. Connect V- to GND for single-supply operation. Positive Analog and Digital Supply-Voltage Input. Internally connected to substrate. Quad, Low-Voltage, TOTAL HARMONIC DISTORTION vs. FREQUENCY 100 -5V 5Vp-p SIGNAL 600 IN AND OUT 10 1 0.1 0. 100 1k FREQUENCY (Hz) FUNCTION MAX4536/7/8 TOC-12 10k 100k 7 ...
Page 8
... This voltage can damage the MAX4536/MAX4537/MAX4538. Even ±5% tolerance supplies may have overshoot or noise spikes that exceed 13.0V. The MAX4536/MAX4537/MAX4538 operate from single supplies between +2.0V and +12V when V- is connect GND. All of the bipolar precautions must be observed. ...
Page 9
... MAX4538 V+ NO1 COM1 V = +3V COM1 COM2 N02 V = +3V COM2 IN LOGIC GND V- INPUT V- C INCLUDES FIXTURE AND STRAY CAPACITANCE. L Figure 2. Break-Before-Make Interval (MAX4538 only) MAX4536 MAX4537 MAX4538 R GEN COM V GEN GND IN Figure 3. Charge Injection _______________________________________________________________________________________ SWITCH LOGIC OUTPUT NO INPUT V OUT ...
Page 10
... Figure 5. Crosstalk MAX4536 MAX4537 MAX4538 CAPACITANCE METER 2. 1MHz V- 10nF V- Figure 7. Channel-On Capacitance MAX4536 V+ 10nF MAX4537 MAX4538 V+ N01 COM1 IN2 IN1 COM2 N02 GND V- 10nF MAX4536 10nF MAX4537 MAX4538 V+ COM 10nF GND 2. 2.4V ...
Page 11
... Plastic DIP 16 Narrow SO 16 QSOP B Dice* 16 Plastic DIP COM2 16 Narrow SO 16 QSOP IN2 16 Plastic DIP 16 Narrow SO IN3 16 QSOP Dice* 16 Plastic DIP 16 Narrow SO 16 QSOP MAX4536 PIN TRANSISTOR COUNT: 121 SUBSTRATE IS INTERNALLY CONNECTED COM1 V+ IN1 IN4 COM4 D (1.37mm GND V- COM3 0.053" ...
Page 12
... B E Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied ...