TLE 7368-3E Infineon Technologies, TLE 7368-3E Datasheet - Page 8
TLE 7368-3E
Manufacturer Part Number
TLE 7368-3E
Description
Manufacturer
Infineon Technologies
Datasheet
1.TLE_7368E.pdf
(41 pages)
Specifications of TLE 7368-3E
Packages
PG-DSO-36
Comment
3 linear post regulators (5V, 3.3/2.6V, 1.3V),selectable StandBy-Vreg (1.0/2.6V) and 2 voltage trackers (5V)
Vq (max)
5.0 V, 3.3/2.6 V, 1.3 V, 1.0/2.6 V
Iq (max)
2,500.0 mA
Iq (typ)
120.0 µA
Output
Linear (Buck Preregulator)
Pin
(TLE7368G)
22
23
24
25, 26
27
28
29
30
31
32, 33
34
35
36
–
Data Sheet
Pin
(TLE7368E)
23
24
25
26, 27
28
29
30
31
32
–
33
34
35
36
Symbol
SEL_LDO2
WDI
WDO
SW
BST
FB/L_IN
Q_LDO1
FB_EXT
DRV_EXT
N.C.
Q_STBY
IN_STBY
MON_STBY Monitoring output for stand-by regulator; power fail active low
GND_A
Function
Selection input LDO2;
Connect to GND to select 2.6 V output voltage for LDO2;
Connect straight to Q_LDO2 to select 3.3 V output voltage for LDO2.
Window Watchdog input;
Apply a watchdog trigger signal to this pin
Window Watchdog output;
Open drain output, active low,
connect external 10 k pull-up resistor to microcontroller I/O voltage
Buck power stage’s output;
Connect both pins directly, on short lines, to the Buck converter circuit,
i.e. the catch diode and the Buck inductance
Bootstrap driver supply input;
Connect the buck power stage’s driver supply capacitor to the SW pins;
For capacitor selection please refer to
Buck converter feedback input plus input for LDO1 and trackers;
Connect the output of the buck converter circuit with short lines to these
pins; For Buck output capacitor selection please refer to
Voltage regulator 1 output;
5 V output; Block to GND with capacitor for stable regulator operation;
Selection of capacitor
Chapter
External regulator feedback input;
Feedback input of control loop for the external power stage regulator.
Connect to the emitter of the regulating transistor; Block to GND with
capacitor for stable regulator operation; Selection of capacitor
C
Bipolar power stage driver output;
Connect the base of an external NPN transistor directly to this pin;
Regarding choice of the external power stage refer to
Internally not connected; Connect to GND_A.
Stand-by regulator output;
Output voltage depending on the state of SEL_STBY; Block to GND
with capacitor for stable regulator operation; Selection of capacitor
C
Input to stand-by regulator;
Always connect the reverse polarity protected battery line to this pin;
Input to all IC internal biasing circuits;
Block to GND directly at the IC with ceramic capacitor; For proper
choice of input capacitors please refer to
output with special timing, open drain, connect external pull-up resistor.
Analog ground connection;
Connect to exposed pad.
Q_FB_EXT
Q_STBY
according to
6.
according to
8
Chapter 4.4
C
Chapter 4.4
Q_LDO1
according to
and
and
Chapter
Chapter
Chapter
Chapter
Chapter 4.4
6.
6.
Rev. 2.1, 2010-11-22
6.
6.
Pin Configuration
Chapter
Chapter
and
TLE7368
6.
6.