TLE 8444SL Infineon Technologies, TLE 8444SL Datasheet
TLE 8444SL
Specifications of TLE 8444SL
Related parts for TLE 8444SL
TLE 8444SL Summary of contents
Page 1
...
Page 2
... Power Supply Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.3.3 Temperature Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.4 Power-Outputs 1-4 (Half Bridge Outputs 5.4.1 Protection and Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5.4.1.1 Short Circuit of Output to Ground 5.4.1.2 Open Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.5 Output Switching Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.5.1 Application Note for Bipolar Stepper Motor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Data Sheet 2 TLE 8444SL Table of Contents Rev. 1.1, 2009-07-07 ...
Page 3
... AEC Qualified Description The TLE 8444SL is a protected Quad-Half-Bridge-IC targeted towards automotive and industrial motion control applications monolithic die based on Infineon’s smart mixed technology SPT which combines bipolar and CMOS control circuitry with DMOS power devices. DC-Motors can be driven in forward (cw), reverse (ccw), brake and high impedance modes where as Stepper- Motors can be driven in No-Current, negative / positive output current modes ...
Page 4
... EF2 Function IN3 OUT3+4 IN4 Figure 1 Block Diagram Data Sheet Vs monitor Internal under/overvoltage Supply detection Error Flag Generation Logic 4 VS Protected Driver Stage OUT1+2 Charge Pump Protected Driver Stage OUT3+4 GND Rev. 1.1, 2009-07-07 TLE 8444SL Block Diagram OUT1 OUT2 OUT3 OUT4 ...
Page 5
... INH, INHH, INHL V V EFx, EFLx V V INx, INHx, Figure 2 Terms Data Sheet INH I INHH TLE8444 EFx I EFLKx INx I INx GND V I INLx GND 5 TLE 8444SL Block Diagram V V DSHSx FU OUTx I OUTx V V DSLSx FL Rev. 1.1, 2009-07-07 ...
Page 6
... EF1 5 20 IN1 6 19 IN2 7 18 EF2 OUT GND 11 14 GND pins must be externally connected together to the S Figure 18 6 TLE 8444SL Pin Configuration n.c. OUT3 VS n.c. GND IN3 IN4 INH n.c. VS OUT 4 n.c. and Figure 19 for more information Rev. 1.1, 2009-07-07 ...
Page 7
... Input Channel of Half-bridge 4 Controls OUT4, Inverting Input with internal Pull Up 19 IN3 Input Channel of Half-bridge 3 Controls OUT3, Non-inverting Intput with internal Pull Down 23 OUT3 Power Output of Half-bridge 3 Short-circuit protected; with integrated free-wheeling diodes Data Sheet 7 TLE 8444SL Pin Configuration Rev. 1.1, 2009-07-07 ...
Page 8
... IN(1-4) V INH V -0.3 EF(1+ OUT(1- EF(1- -50 stg V V pin vers ESD V -2 ESD 8 TLE 8444SL General Product Characteristics Limit Values Unit Conditions Max – 5 < 5 < – – 150 C – 150 C – ...
Page 9
... V -0 -0.3 IN(1-4) V INH T -40 j Symbol Limit Values Min. Typ – – thJSP R – 60 thJA 9 TLE 8444SL General Product Characteristics Unit Conditions Max – Limit values, OV OFF deviations possible; V After rising above Outputs are open ...
Page 10
... ONL dOFFL t 0 OFFL t 0.1 2 – – TLE 8444SL General Product Characteristics Unit Conditions 13 < IN1+3=L, IN2+4 increasing, see Figure decreasing, see Figure see Figure ...
Page 11
... SLEEP V – 0.2 0.4 EFL(1+2) I – – 10 EFLK(1+2) t – dEF T 150 175 200 jSD T 125 – 175 jSO 11 TLE 8444SL General Product Characteristics Unit Conditions 0.4 A, INH = LOW F V – V – V – V – V – IN(1+ 0.8V IN(2+4) V – V – V – V ...
Page 12
... Sleep Mode The TLE 8444SL can be placed in low current-consumption mode (or sleep mode) by setting the input, INH pin to LOW. The INH pin has an internal pull-down current source. In sleep-mode, all output transistors are switched off. An output disable and enable time is specified and this behavior is shown in ...
Page 13
... Reverse Polarity The TLE 8444SL requires an external reverse polarity protection. This protection is essential to avoid an undesired I reverse current ( ) to flow from ground potential to battery causing excessive power dissipation across the RB diodes in the event of reverse polarity. Hence a reverse polarity protection diode is recommended GND a) HSx ...
Page 14
... Sleep Mode (Low current consumption mode current (both low side transistors turned-ON negative phase current current (both low side transistors turned-ON current (both high side transistors turned-ON positive phase current 14 TLE 8444SL Block Description Figure 19 and Figure 21). Rev. 1.1, 2009-07-07 ...
Page 15
... High side transistor is turned-ON Low side transistor is turned-OFF 1 = Logic HIGH Low side transistor is turned-ON High side transistor is turned-OFF X = don’t care X = don’t care |Z| = High- and Lowside transistor are turned-OFF (Output in Tristate, High Z) Data Sheet 15 TLE 8444SL Block Description Rev. 1.1, 2009-07-07 ...
Page 16
... OFF. The Error Flag however OVOFF (Figure 6). A switching hysteresis is implemented at both Figure Error Flag behavior Output status - latch auto recovery auto recovery 16 TLE 8444SL Block Description as shown in Figure 9. Changing the INHIBIT SC in ON-state for longer than the OLD filter time d_OLD ) and above the UVOFF 8) ...
Page 17
... OVOFF falls again and reaches the switch on voltage OVOFF V UVHY V UVON undervoltage without error signalling t d_EF t d_EF 17 TLE 8444SL Block Description Figure 1). Figure 7 , the power stages UVON V OVHY V OVON t t overvoltage with error signalling t d_EF ...
Page 18
... jSD V OUTx ON High Z no Error Status overtemperature error error EF t d_EF d_EF Block Description VS V UVON (max) , the overtemperature Error jSD Figure 8 below. T jSO d_EF t t d_EF t Rev. 1.1, 2009-07-07 TLE 8444SL , jSO ...
Page 19
... The output stage stays off and the corresponding diagnostics output information is set until INHIBIT toggles to low and high again or a power-on reset is performed. (refer to Data Sheet Figure OUT Figure 13) 19 TLE 8444SL Block Description for longer than the shutdown delay SD t dSD t Rev. 1.1, 2009-07-07 ...
Page 20
... GND Limit + - Delay t d Error Flag Generation Delay + - CHP HS-Driver 1 HS-Dirver 2 Current Limit + - Delay TLE 8444SL Block Description Lowside Power Transistor R R sense sense overcurrent openload Power GND R sense overcurrent Rev. 1.1, 2009-07-07 OUT ...
Page 21
... Shut down all output stages RF-Blanking RF-Blanking Shut down all output stages t RR ERROR-FF R POR & OR3 & OCD S >1 OLD 21 TLE 8444SL Block Description OR6 >1 Level-Shift Q Q OR5 >1 Level-Shift Error-Interface Rev. 1.1, 2009-07-07 EF2 GND EF1 GND ...
Page 22
... If a short circuit of a halfbridge output to GND is present, the device will behave like displayed in INH active mode OUTx d_SD Figure 13 Overcurrent signalling Data Sheet t SLEEP active mode sleep mode t d_en 22 TLE 8444SL Block Description Figure 13 below d_SD Rev. 1.1, 2009-07-07 ...
Page 23
... IN2 I OUT12 I OLD OUT1 V OUT2 Figure 15 Open Load signalling Data Sheet OLD OUT 1 M OUT d_OLD d_OLD 23 TLE 8444SL Block Description in ON-state for longer than the open-load Figure Open Load d_OLD Rev. 1.1, 2009-07-07 14, ...
Page 24
... V INx H L IOUT 100 no current Vs - 100 t doffL Figure 16 Switching Time Definitions Data Sheet Figure 17. 50% t donH t onH 90 10% 10% 90% t offL 24 TLE 8444SL Block Description 50% t doffH t offH 90 10% 10% 90% t onL t donL Rev. 1.1, 2009-07- ...
Page 25
... INH=High INx Figure 17 Switching Time Characterization Circuit Data Sheet V S HSx IOUT A LSx TLE8444 GND 25 TLE 8444SL Block Description 100 x OUTx 100 Rev. 1.1, 2009-07-07 ...
Page 26
... EF1 pin 4,9,15,22) EF OUT INH OUT OUT IN 4 OUT GND ( pin 1,2,11,12, 20) 26 TLE 8444SL Block Description BAT 100k 100nF 100 Single Two Motor ...
Page 27
... Q TLE4678 EF1 EF2 pin 4,9,15,22 INH GND ( pin 1,2,11,12, 20) 27 TLE 8444SL Block Description BAT 100k Watchdog Adjust Input 100nF 100 OUT 1 OUT 2 OUT 3 ...
Page 28
... GND Figure 20 Reversing the current in fullbridge operation to achieve a stepper motor movement Data Sheet Figure 20 below. Picture a) on the left hand side shows HS2 HS1 OUT2 OUT1 LS1 LS2 b 28 TLE 8444SL Block Description Vs HS2 L phase OUT2 R phase LS2 GND Rev. 1.1, 2009-07-07 ...
Page 29
... Low I OUT12 +Iload 0 -Iload IN3 IN4 High Low 90° Phaseshift I OUT34 +Iload 0 -Iload Figure 21 Bipolar stepper motor control (full step mode) Data Sheet 21. Normally, the output switching frequency is lower (approx. < 2kHz). This 29 TLE 8444SL Block Description Rev. 1.1, 2009-07-07 ...
Page 30
... Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. Data Sheet B 0.1 B Seating Plane 24x TLE 8444SL Package Outlines 0.35 x 45˚ 3.9 ±0.1 8˚ MAX. 0˚...8˚ 6 ±0.2 C 0.2 ...
Page 31
... Revision History 0.40.3 TLE 8444SL Revision History: Rev. 1.1, 2009-07-07 Version Subjects (major changes since last revision) 1.1 Package Illustration on overview sheet corrected from exposed pad to standard SSOP package 1.0 Final Data Sheet Release Data Sheet 31 TLE 8444SL Revision History Rev. 1.1, 2009-07-07 ...
Page 32
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...