BTS 4130QGA Infineon Technologies, BTS 4130QGA Datasheet
BTS 4130QGA
Specifications of BTS 4130QGA
Related parts for BTS 4130QGA
BTS 4130QGA Summary of contents
Page 1
...
Page 2
... ST0/1/2/3 Signal in Case of Failures 18 7.2.1 Diagnostic in Open Load, Channel OFF 19 7.2.2 ST 0/1 Signal in case of Over Temperature 20 7.3 Electrical Characteristics Diagnostic Functions 21 8 Input Pins 22 8.1 Input Circuitry 22 8.2 Electrical Characteristics 22 9 Application Information 23 9.1 Further Application Information 23 10 Package Outlines 24 11 Revision History 25 Datasheet 2 BTS 4130QGA 1.0, 2008-27-02 ...
Page 3
Smart High-Side Power Switch Four Channel Device 1 Overview Basic Features • Withstand low Cranking Voltage • Fit for 12V Application • Four Channel device • Very low Stand-by Current • CMOS Compatible Inputs • Electrostatic Discharge Protection (ESD) • ...
Page 4
Diagnostic Feature • Open load detection in OFF state • Feedback of the thermal shutdown in ON state • Diagnostic feedback with open drain output Protection Functions • Short circuit protection • Overload protection • Current limitation • Thermal shutdown ...
Page 5
Block Diagram Channel 0 IN0 protection ST 0/1 Channel 1 IN1 Channel 2 IN2 protection ST 2/3 Channel 3 IN3 Figure 1 Block diagram for the BTS4130QGA Data Sheet voltage sensor internal power over supply temperature clamp for inductive ...
Page 6
Pin Configuration 3.1 Pin Assignment GND0/1 GND2/3 Figure 2 Pin Configuration 3.2 Pin Definitions and Functions Pin Symbol Function 1, 10, 11, V Battery voltage; Design the wiring for the simultaneous maximum short circuit S 12, 15, 16, currents ...
Page 7
Pin Symbol Function 13 OUT3 Output 3; Protected High side power output channel 3 14 OUT2 Output 2; Protected High side power output channel 2 17 OUT1 Output 1; Protected High side power output channel 1 18 OUT0 Output 0; ...
Page 8
General Product Characteristics 4.1 Absolute Maximum Ratings 1) Absolute Maximum Ratings T = 25°C; (unless otherwise specified) J Pos. Parameter Voltages 4.1.1 Supply voltage 4.1.2 Reverse polarity Voltage 4.1.3 Supply voltage for short circuit protection Input pins 4.1.4 Voltage ...
Page 9
Note: Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. 4.2 Functional Range T ...
Page 10
Power Stage The power stages are built by an N-channel vertical power MOSFET (DMOS) with charge pump. 5.1 Output ON-State Resistance R The ON-state resistance DS(ON) shows the dependencies for the typical ON-state resistance. The behavior in reverse polarity ...
Page 11
Inductive Output Clamp When switching OFF inductive loads with high side switches, the voltage V because the inductance intends to continue driving the current. To prevent the destruction of the device due to high voltages, there is a voltage ...
Page 12
Maximum Load Inductance During demagnetization of inductive loads, energy has to be dissipated in the BTS4130QGA. This energy can be calculated with following equation Following equation simplifies under the assumption of R The energy, which is ...
Page 13
Electrical Characteristics Power Stage Electrical Characteristics: Power stage - +150 C. Typical values are given Pos. Parameter 5.4.1 ON-state resistance per channel 5.4.2 Nominal load current per channel ...
Page 14
Protection Mechanisms The device provides embedded protective functions. Integrated protection functions are designed to prevent the destruction of the IC from fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions ...
Page 15
In the case the supply voltage is in between of follow the input least one channel state, parameters are no longer warranted and lifetime is reduced compared to normal mode. This specially impacts the short ...
Page 16
Current Limitation At first step, the instantaneous power in the switch is maintained to a safe level by limiting the current to the maximum current allowed in the switch the current flowing in the DMOS. At thermal shutdown, the ...
Page 17
Electrical Characteristics Protection Functions Electrical Characteristics: Protection - +150 C. Typical values are given Pos. Parameter Loss of ground 6.6.1 Output leakage current while GND disconnected Reverse polarity ...
Page 18
Diagnostic Mechanism For diagnosis purpose, the BTS4130QGA provides status pin. 7.1 ST 0/1/2/3 Pin BTS4130QGA status pins are an open drain, active low circuit “hard” failure mode occurs (Short circuit to GND / Over temperature or open ...
Page 19
Diagnostic in Open Load, Channel OFF For open load diagnosis in OFF-state, an external output pull-up resistor ( of the pull-up resistor value, the leakage currents and the open load threshold voltage account. Figure 13 gives a sketch of ...
Page 20
ST 0/1 Signal in case of Over Temperature In case of over temperature, the junction temperature reaches the thermal shutdown temperature In that case, the ST 0/1 signal is toggling between IN V OUT ST 0 ...
Page 21
Electrical Characteristics Diagnostic Functions Electrical Characteristics: Diagnostics - +150 C. Typical values are given Pos. Parameter Load condition threshold for diagnostic 7.3.1 Open Load detection voltage ST 0/1 ...
Page 22
Input Pins 8.1 Input Circuitry The input circuitry is CMOS compatible. The concept of the Input pin is to react to voltage transition and not to voltage threshold. With the Schmidt trigger impossible to have the device ...
Page 23
Application Information Note: The following information is given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the device. V ...
Page 24
Package Outlines 1.27 +0. Index Marking 1) Does not include plastic or metal protrusions of 0.15 max per side 2) Does not include dambar protrusion of 0.05 max per side Figure 18 PG-DSO-20-32 (Plastic Dual ...
Page 25
Revision History Version Date Changes 1.0 2008-03-18 Creation of the data sheet Data Sheet 25 BTS4130QGA Revision History Rev. 1.0, 2008-03-18 ...
Page 26
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...