LTC2356CMSE-14 Linear Technology Corporation, LTC2356CMSE-14 Datasheet
LTC2356CMSE-14
Available stocks
Related parts for LTC2356CMSE-14
LTC2356CMSE-14 Summary of contents
Page 1
... LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. 3.3V ...
Page 2
... 100MHz ORDER PART NUMBER LTC2356CMSE-12 10 CONV LTC2356IMSE-12 9 SCK LTC2356CMSE-14 8 SDO LTC2356IMSE-14 6 GND MSE PART MARKING = 150°C/ W LTCWN LTCWN LTCVF LTCVF http://www.linear.com/leadfree/ = 3.3V LTC2356-14 MAX MIN TYP MAX UNITS 14 ± ...
Page 3
ACCURACY otherwise specifications are 25°C with external reference = 2.55V DC. Differential signal drive with SYMBOL PARAMETER CONDITIONS SINAD Signal-to-Noise Plus 100kHz Input Signal ...
Page 4
LTC2356-12/LTC2356- POWER REQUIRE E TS range, otherwise specifications are at T SYMBOL PARAMETER V Supply Voltage DD I Supply Current DD P Power Dissipation CHARACTERISTICS range, otherwise specifications are at T SYMBOL ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS SINAD vs Input Frequency 0 FREQUENCY (MHz) SFDR vs Input Frequency 0.1 1 ...
Page 6
LTC2356-12/LTC2356- TYPICAL PERFOR A CE CHARACTERISTICS Differential Linearity vs Output Code 1.0 0.8 0.6 0.4 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 0 8192 4096 OUTPUT CODE Differential and Integral Linearity vs Conversion Rate MAX ...
Page 7
W U TYPICAL PERFOR A CE CHARACTERISTICS PSRR vs Frequency –25 –30 –35 –40 –45 –50 –55 –60 –65 – 100 1k 10k FREQUENCY (Hz) Internal Reference Voltage vs V 2.4902 2.4900 2.4898 2.4896 2.4894 2.4892 2.4890 2.6 ...
Page 8
LTC2356-12/LTC2356- CTIO (Pin 1): Noninverting Analog Input fully differentially with respect to A 1.25V differential swing with respect common mode swing. DD – A (Pin 2): Inverting ...
Page 9
DIAGRA SCK t 4 CONV t 6 INTERNAL SAMPLE S/H STATUS t 8 Hi-Z SDO *BITS MARKED "X" AFTER D0 SHOULD BE IGNORED ...
Page 10
LTC2356-12/LTC2356- APPLICATIO S I FOR ATIO DRIVING THE ANALOG INPUT The differential analog inputs of the LTC2356-12/LTC2356-14 may be driven differentially single-ended input (i.e., the – A input is set Both differential ...
Page 11
U U APPLICATIO S I FOR ATIO INPUT FILTERING AND SOURCE IMPEDANCE The noise and the distortion of the input amplifier and other circuitry must be considered since they will add to the LTC2356-12/LTC2356-14 noise and distortion. The small-signal bandwidth ...
Page 12
LTC2356-12/LTC2356- APPLICATIO S I FOR ATIO Figure 3. The voltage of the external reference must be higher than the 2.5V output of the internal reference. The recommended range for an external reference is 2.55V ...
Page 13
U U APPLICATIO S I FOR ATIO 0 –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 0 185k 371k 556k FREQUENCY (Hz) Figure 6b. LTC2356-12 6MHz Sine Wave 4096 Point FFT Plot with the LT1819 Driving ...
Page 14
LTC2356-12/LTC2356- APPLICATIO S I FOR ATIO internal reference. Note that, for slower conversion rates, the Nap and Sleep modes can be used for substantial reductions in power consumption. DIGITAL INTERFACE The LTC2356-12/LTC2356-14 has a 3-wire SPI-compatible (Serial Protocol ...
Page 15
... LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... DACs LTC1592 16-Bit, Serial SoftSpan References LT1790-2.5 Micropower Series Reference in SOT-23 LT1461-2.5 Precision Voltage Reference LT1460-2.5 Micropower Series Voltage Reference SoftSpan is a trademark of Linear Technology Corporation. Linear Technology Corporation 16 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 ● NC7SVU04P5X 0.1µ ...