74ACTQ245SC Fairchild Semiconductor, 74ACTQ245SC Datasheet - Page 7

• Manufacturer Part Number: 74ACTQ245SC
• Description: IC TRANSCVR TRI-ST 8BIT 20SOIC
• Manufacturer: Fairchild Semiconductor
• Series: 74ACTQr

Specifications of 74ACTQ245SC

• Logic Type: Transceiver, Non-Inverting
• Number Of Elements: 1
• Number Of Bits Per Element: 8
• Current - Output High, Low: 24mA, 24mA
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (7.5mm Width)
• Logic Family: 74ACT
• Number Of Channels Per Chip: 8
• Input Level: TTL
• Output Level: CMOS
• Output Type: 3-State
• High Level Output Current: - 24 mA
• Low Level Output Current: 24 mA
• Propagation Delay Time: 7 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Maximum Operating Temperature: + 85 C
• Function: Octal Bidir Trans
• Input Bias Current (max): 4 uA
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Number Of Circuits: 8
• Polarity: Non-Inverting
• Operating Supply Voltage (typ): 5V
• Number Of Elements: 1
• Number Of Channels: 8
• Input Logic Level: TTL
• Output Logic Level: CMOS
• Package Type: SOIC W
• Logical Function: Bus Transceiver
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Technology: CMOS
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 74ACTQ245SC.

©1989 Fairchild Semiconductor Corporation
74ACQ245, 74ACTQ245 Rev. 1.5.1
FACT Noise Characteristics
The setup of a noise characteristics measurement is crit-
ical to the accuracy and repeatability of the tests. The
following is a brief description of the setup used to mea-
sure the noise characteristics of FACT.
Equipment:
Procedure:
1. Verify Test Fixture Loading: Standard Load 50pF,
2. Deskew the HFS generator so that no two channels
3. Terminate all inputs and outputs to ensure proper
4. Set the HFS generator to toggle all but one output at
5. Set the HFS generator input levels at 0V LOW and 3V
Notes:
14. V
15. Input pulses have the following characteristics:
Hewlett Packard Model 8180A Word Generator
PC-163A Test Fixture
Tektronics Model 7854 Oscilloscope
Figure 1. Quiet Output Noise Voltage Waveforms
500 .
have greater than 150 ps skew between them. This
requires that the oscilloscope be deskewed first. It is
important to deskew the HFS generator channels
before testing. This will ensure that the outputs switch
simultaneously.
loading of the outputs and that the input levels are at
the correct voltage.
a frequency of 1 MHz. Greater frequencies will
increase DUT heating and effect the results of the
measurement.
HIGH for ACT devices and 0V LOW and 5V HIGH for
AC devices. Verify levels with an oscilloscope.
reference.
f
OHV
1MHz, t
and V
r
OLP
3ns, t
are measured with respect to ground
f
3ns, skew
150ps.
7
V
V
OLP
ILD
Determine the quiet output pin that demonstrates the
greatest noise levels. The worst case pin will usually
be the furthest from the ground pin. Monitor the output
voltages using a 50 coaxial cable plugged into a
standard SMB type connector on the test fixture. Do
not use an active FET probe.
Measure V
the worst case transition for active and enable.
Measure V
the worst case active and enable transition.
Verify that the GND reference recorded on the
oscilloscope has not drifted to ensure the accuracy
and repeatability of the measurements.
Monitor one of the switching outputs using a 50
coaxial cable plugged into a standard SMB type
connector on the test fixture. Do not use an active
FET probe.
First increase the input LOW voltage level, V
the output begins to oscillate or steps out a min of 2ns.
Oscillation is defined as noise on the output LOW
level that exceeds V
that exceed V
which oscillation occurs is defined as V
Next decrease the input HIGH voltage level, V
the output begins to oscillate or steps out a min of 2ns.
Oscillation is defined as noise on the output LOW
level that exceeds V
that exceed V
which oscillation occurs is defined as V
Verify that the GND reference recorded on the
oscilloscope has not drifted to ensure the accuracy
and repeatability of the measurements.
Figure 2. Simultaneous Switching Test Circuit
and V
/V
OLV
IHD
and V
OLP
OHP
:
IH
IH
and V
and V
limits. The input HIGH voltage level at
limits. The input LOW voltage level at
OHP
IL
IL
/V
OLV
OHV
limits, or on output HIGH levels
limits, or on output HIGH levels
OHV
on the quiet output during
on the quiet output during
:
ILD
IHD
www.fairchildsemi.com
.
.
IL
, until
IH
, until