HS1E IDEC Corporation, HS1E Datasheet - Page 11

• Manufacturer Part Number: HS1E
• Description: Hs1e Series Full Size Interlock Switch With Locking Solenoid
• Manufacturer: IDEC Corporation

Applicable Crimping Terminals
• (Refer to the Crimping Terminal 1 or 2 shown in the drawing below.)
• HS1C
• HS1B
Installation Examples (see the diagrams below)
www.idec.com
Terminals No. 1 to 6: Use solid or stranded wires only (crimping ter-
minals not applicable).
Terminals No. 7 and 8: Crimping Terminal 1
Ground Terminal:
Ground Terminal: Crimping Terminal 2
Other Terminals: Crimping Terminal 1
HS2B, HS5B, and HS1E
Crimping Terminal 1
L1 ( mm )
Crimping Terminal 1
Use an insulation tube on the crimping terminal.
3.6 min.
ø3.6 min.
Wire
Insulation Tube
Approx. 4mm
Mounting on Sliding Doors
Crimping Terminal 2
Safety Products
HS9Z-A2 Actuator
3.5 max.
Mounting on Hinged Doors
Door Stop
HS9Z-A1 Actuator
Door
L1 ( mm )
Crimping Terminal 2
USA: (800) 262-IDEC or [phone], Canada: (888) 317-IDEC
3.5 min.
ø4.1 min.
Latch
Crimping Terminal
HS9Z-A1 Actuator
3.8 max.
Operation Precautions
Applicable Connectors (As shown below)
• Use connectors which maintain the IP67 protection.
• Applicable Connector Dimensions
• Flex Conduit: VF03 (Japan Flex) www.nipolex.co.jp
• Steel Connector (G1/2): ALC-103
Recommended Screw Tightening Torque
• HS1C: 5.0±0.5 N-m (approx. 50±5 kgf-cm)
• HS1B: 5.0±0.5 N-m (approx. 50±5 kgf-cm)
• HS2B: 5.0±0.5 N-m (approx. 50±5 kgf-cm)
• HS5B: 4.0±0.4 N-m (approx. 40±4 kgf-cm)
• HS1E: 5.0±0.5 N-m (approx. 50±5 kgf-cm)
• Key (HS9Z-A1/A2)
• (2 pcs. of M6 hex socket head cap screws)
• 2.0±0.2 N-m (approx. 20±2 kgf·cm)
• 1.0±0.2 N-m (approx. 10±2 kgf·cm)
Applicable Wire Size
• HS1C: 0.5 to 0.75 mm2 (Terminals No.1, 2, 5 to 8)
• HS5B: 0.5 to 1.25 mm2
• HS1E: 0.5 to 1.25 mm2
(4 or 6 pcs of M5 hex socket head cap screws)
(2 or 4 pcs. of M5 hex socket head cap screws)
(2 pcs of M5 hex socket head cap screws)
(2 pcs of M4 hex socket head cap screws)
(4 or 6 pcs of M5 hex socket head cap screws)
5.0±0.5 N-m (approx. 50±5 kgf·cm)
Key (HS9Z-A51/A52)
(2 pcs of M4 hex socket head cap screws)
(2 pcs of M4 Phillips screws)
1.0 to 1.25 mm2 (Terminals No.3, 4, and
grounding terminal)
The screws are supplied by the user.
(PF13.5): RBC-103PG13.5
G1/2 or PG13.5
9 mm max.
Precautions
B1-45
B1