D2SW Omron Corporation, D2SW Datasheet
![no-image](/images/no-image-200.jpg)
D2SW
Available stocks
Related parts for D2SW
D2SW Summary of contents
Page 1
... Note: 1. The standard lengths of the lead wires (AWG22) of models incorporating them are 30 cm (12 in). Model Model 3 A Model 0.1 A D2SW-3HS D2SW-01HS D2SW-3TS D2SW-01TS D2SW-3DS D2SW-01DS D2SW-3MS D2SW-01MS D2SW-3L1HS D2SW-01L1HS D2SW-3L1TS D2SW-01L1TS D2SW-3L1DS D2SW-01L1DS D2SW-3L1MS D2SW-01L1MS D2SW-3L3HS D2SW-01L3HS D2SW-3L3TS D2SW-01L3TS D2SW-3L3DS D2SW-01L3DS D2SW-3L3MS D2SW-01L3MS D2SW-3L2HS D2SW-01L2HS D2SW-3L2TS D2SW-01L2TS D2SW-3L2DS D2SW-01L2DS D2SW-3L2MS D2SW-01L2MS Snap Action Switch D2SW 1 ...
Page 2
... D2SW-01 600 VAC, 50/60 Hz for 1 min. between con- tacts of the same polarity — — 200,000 operations min. Lead wire model D2SW-3L2@S D2SW-3MS D2SW-01L2@S D2SW-01MS 60 g 180 — 0.6 mm 1.0 mm 0.5 mm 0.8 mm 0.1 mm 19.3 mm — 14.5±0.8 mm 8.4±0.3 mm ...
Page 3
... SPST- Consult Omron for ordering information Inductive load Inductive load Motor load 0 0.5 A 0.3 A 0 Inductive load Inductive load Motor load — — SPST-NO ( Consult Omron for ordering information D2SW Snap Action Switch ...
Page 4
... Simulated Roller Lever D2SW-3L3@S D2SW-01L3@S ■ Hinge Roller Lever D2SW-3L2@S D2SW-01L2@S Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions. 2. The above illustrations and dimensions are for models with solder terminals. Refer to “Terminals” for models with tab (#110) and PCB terminals ...
Page 5
... The above illustrations and dimensions are for models with pin plungers. The dimensions and operating characteristics of the actuators of models incorporating them are the same as those of the actuators of models with both actuators and terminals. ■ Terminals Solder Terminals PCB Terminals Note: Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions. Tab Terminals (#110) PCB Mounting D2SW Snap Action Switch 5 ...
Page 6
... Tighten the screws to a torque of 0.23 to 0.26 N • m (2.3 to 2.7 kgf • cm) Mounting holes When soldering a lead wire to a terminal of the D2SW, use a solder- ing iron with a maximum capacity and do not take more than 5 seconds to solder the lead wire, otherwise the characteristics of the D2SW may be altered ...
Page 7
... Severability: If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. ) related to any claim, investigation, litigation or proceeding ) which arises or is alleged to arise from Buyer's acts or shall indemnify and (at its own expense) (without regard to conflict of laws) D2SW Snap Action Switch including . Federal 7 ...
Page 8
... COMPONENTS LLC 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 Cat. No. J01C-E-01 01/07 D2SW 8 Snap Action Switch 2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof. 3. Performance Data. Performance data given in this publication is provided as a guide for the user in determining suitability and does not constitute a war- ranty ...