TYPHOON800 rfsolutions.ltd, TYPHOON800 Datasheet
TYPHOON800
Related parts for TYPHOON800
TYPHOON800 Summary of contents
Page 1
RS232/485 R • Wireless half duplex radio modem RS232 and RS485 serial interfaces • RF power output 10mW • Range up to 800m • Radio baud rate up to 10kbps • • Serial baud rate up to 38.4kbp/s • Housed ...
Page 2
RS232/485 R Technical Specification ..................................................................................................................... 3 1.1 Functional description ........................................................................................................ 3 1.2 Functional Characteristics.................................................................................................. 3 1.2.1 General ....................................................................................................................... 3 1.2.2 Transmission............................................................................................................... 3 1.2.3 Reception .................................................................................................................... 4 1.2.4 DC ............................................................................................................................... 4 1.3 Status LEDs ....................................................................................................................... 4 1.4 Power Supply ..................................................................................................................... 4 ...
Page 3
RS232/485 R 1.1 Functional description The RF modem is configurable as a ‘transparent’ wireless serial point-to-point link, reproducing the function of a half duplex serial cable. An addressed secured mode is also supported. The RF modem can be configured to ...
Page 4
RS232/485 R 1.2.3 Reception Specification Sensitivity for CER <10 Average CER Saturation for CER <10 Selectivity 1.2.4 DC Specification Power supply Current consumption 1.3 Status LEDs The RF Modem has several LEDs that represent the status of the power supply ...
Page 5
RS232/485 R parameter for flow-control management must be set to “hardware - use CTS/RTS” (register S216=0). 1.5.2 RS232 Serial Link RS232 connections are made using both TB1 and TB2 or by inserting a DB9 plug into J5: Wire this end ...
Page 6
RS232/485 R 1.5.3 RS485 Serial Link RS485 connections are made using both TB1 and TB2 or by inserting a DB9 serial cable into J5. Pin Name Description 1 GND Ground, 0Vdc 2 TXB Transmit data ‘-‘ From the host 3 ...
Page 7
RS232/485 R 1.6 Antenna The RF modem is supplied with an 868MHz ¼ wave whip antenna that has been carefully matched to the impedance of the RF modem’s power amplifier 1.7 Temperature Range Storage temperature: 4 Operating temperature : 1.8 ...
Page 8
... In the Settings menu change the user level to advanced. From the Modem menu Serial port configuration and select 19,000bps. 5. From the Tools menu select Terminal and open a terminal window on the COM port connected to the modem. You can now type text into the terminal window, if the Port is opened (By pressing the ‘ ...
Page 9
RS232/485 R The RF modem is able to operate in several different modes which can be configured by setting the values of the appropriate special registers using AT commands. 3 Hayes or ‘AT’ Mode The Hayes or 'AT' commands comply ...
Page 10
RS232/485 R 'ATR’: Hayes registers reset to default values This command allows the user to reset ALL the stored EEPROM registers to their default values (see section 2.9 for register descriptions) 'ATP’: Switch to Stand-by mode This command allows the ...
Page 11
RS232/485 R Example: "002=Hello" indicates that data frame "Hello" comes from Client No.2. o You can add one frame ending character: Carriage Return<CR>, after each received frame. • This in order to distinguish each frame. Example: "002=145<CR> 003=187<CR>" indicates data ...
Page 12
RS232/485 R The RF modem offers several possible configurations using a set of parameters. The parameters are stored in registers and have default values. The values can be modified from the default or interrogated using Hayes commands. The registers are ...
Page 13
RS232/485 R 4.2 Operation Access Register Operation Mode R/W S220 R/W S221 R/W S223 4.3 Network Control Access Register Addressed Secured Mode R/W S252 R/W S256 DS510-1 Aug 2008 M ADIO ODEM Name Description Operation Mode of the Modem. Function ...
Page 14
RS232/485 R 4.4 Radio Test Commands These AT commands are provided to enable measurements during continuous transmission to be taken and are primarily used during radio tests (radiated power, bandwidth, etc.) to show conformance to the ETS 300 220 standard. ...