LED-128G032 Vishay, LED-128G032 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/6/697/vishay_sml.jpg)
LED-128G032
Manufacturer Part Number
LED-128G032
Description
128 X 32 Graphics Display With Drive Electronics And +5v Hc Cmos Level Video Interface
Manufacturer
Vishay
Datasheet
1.LED-128G032.pdf
(3 pages)
INTERFACE SIGNAL DESCRIPTION
DOT CLOCK - This signal enters the SERIAL DATA on each
low to high transition. A total of 128 DOT CLOCK transitions
must be present for each line of column/anode data.
SERIAL DATA - This signal presents the pixel data in positive
logic format. A logic one represents a lit pixel and a logic
zero represents an extinguished pixel. Data is entered from
right to left. The first pixel data entered will represent the left
most pixel in the row.
COLUMN LATCH - This signal latches the pixel data into
the driver outputs. When the COLUMN LATCH signal goes
to logic one the data entered previously will fall through to
the driver outputs. When the signal returns to a logic zero
the data is latched and the shift register is now ready to accept
the next row of data. Must be held low while entering new
SERIAL DATA.
DISPLAY ENABLE - This signal enables the output drivers.
Using a duty cycle control, this signal may also be used for
intensity control. The DISPLAY ENABLE must be at logic
zero before the COLUMN LATCH signal transitions. To avoid
display blurring, the ROW CLOCK signal should also
transition while DISPLAY ENABLE is a logic zero.
ROW DATA - This signal is the first line marker for the scan.
This input should be held high to correspond to the first row
of pixel data.
ROW CLOCK - This signal clocks ROW DATA on the falling
edge. The ROW CLOCK signal is repetitive and must be
present for proper scanning of the display module.
The LED-128G032 has an unique input protection circuit that
assures the column drivers stay blanked on power up. The
protection circuit unblanks the column drivers when the ROW
CLOCK signal begins (i.e the display begins scanning.)
LED-128G032
Vishay Dale
www.vishay.com
14
PIN DESCRIPTION
J1 - POWER CONNECTOR
Tyco AMP #640445-8 or equivalent.
Mates with Tyco AMP 640428-8, MOLEX 09-50-3081 or equivalent.
PIN
1
2
3
4
5
6
7
8
J2 - DATA CONNECTOR
Tyco AMP #103309-2 or equivalent.
Mates with Tyco AMP 746195-2, MOLEX 39-27-1146 or equivalent.
PIN
1
3
5
7
9
11
13
J3 - POWER CONNECTOR
Tyco AMP #641737-1 or equivalent.
Mates with Tyco AMP 1-480424-0 housing and 60617-4 socket terminals
PIN
1
2
3
4
DESCRIPTION
DISPLAY ENABLE
ROW DATA
ROW CLOCK
COLUMN LATCH
DOT CLOCK
SERIAL DATA
No connect
SIGNAL
n/c
n/c
KEY
GND
GND
V
RESERVED
n/c
SIGNAL
RESERVED
GND
GND
V
cc
cc
PIN
2
4
6
8
10
12
14
DESCRIPTION
no connection
no connection
Used to key connector
GND
GND
Logic and LED drive supply
no connection
no connection
DESCRIPTION
no connection
Logic and LED drive supply
For Technical Questions, Contact: Displays@vishay.com
DESCRIPTION
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
ORDERING INFORMATION
DESCRIPTION
Display, Driver Electronics and +5V HC CMOS Interface . LED-128G032
J2 Data Connector Kit (2pcs. recommended) ........... 280105-05
J1 Power Connector Kit ............................................. 280108-12
J3 Power Connector Kit ............................................. 280108-05
Row Data
Row Clock
Display Enable
Row Clock
Column Latch
Display Enable
Serial Data
Dot Clock
PARAMETER
LOGIC AND DATA TIMING
t
t
t
t
t
t
t
1
2
3
4
5
6
7
t
1
1st bit of row will appear in leftmost column
0
t
t
MINIMUM TYPICAL MAXIMUM
6
5
0
0
100
1
25
75
75
5
1
-
1
1
Positive Edge x 128
t
2
2
2
2
t
70
t
3
-
-
-
-
-
-
4
126
Document Number: 37079
30
127
30
Revision 29-Sep-05
t
200
31
7
PART NUMBER
-
-
-
-
-
-
31
0
0
UNITS
1
nS
uS
uS
Hz
nS
nS
nS
1