MIL-C-5015 ITT Industries, MIL-C-5015 Datasheet - Page 4

• Manufacturer Part Number: MIL-C-5015
• Description: Firewall Connectors
• Manufacturer: ITT Industries

MIL-C-5015 Firewall Connectors
MS-K Contacts and Crimp Tools can be ordered separately
*NOTE: For MS-K Assembly it is not neccessary to remove the ceramic retaining ring used on sizes 16
and 12 contacts for MS-K providing that the crimp tool M22520/1-01 is used with the TH119 turret.
However, the formica ring must be removed if using the crimp tools listed below.
*These contacts must be used when ordering contact arrangments 24-28 pin or socket, 28-21 pin or socket, and 20-27 socket only.
†Crimp heads are only applicable for contact sizes 8, 4, and 0.
Assembly Instructions
Contacts, Crimp Tools, Contact Kit Part Numbers
16-Pin
8S-36
16 Pin*
8S-36
16 Socket
8S-16S
16 Socket
12-36
16 Socket*
12-36
12 Pin
12 Socket
8 Pin
8 Socket
4 Pin
4 Socket
0 Pin
0 Socket
Contact Size
STEEL BARREL
330-0187-000
030-1154-000
031-0497-000
031-0498-000
031-0728-000
330-0188-000
031-0499-000
330-0189-000
031-0500-000
330-0190-000
031-0501-000
330-0191-000
031-0502-000
Part Number
STEEL COUPLING NUT
Wire Accom.
16-18-20
16-18-20
16-18-20
16-18-20
16-18-20
12-14
12-14
8
8
4
4
0
0
Recommended Procedures
*
1. Remove Formica retaining ring (or the ce-
2. Crimp contact to wire.
3. Slip endbell (or junction shell), retaining ring,
4. Push contact thru rear insulator. (Contact
ramic retaining ring) from contact (Figure 1).
and washer over wire bundle.
should extend sufficiently to accomplish
Step 5.)
FRONT
INSULATOR
MS22520/1-01
MS3191-1
MS22520/1-01
MS3191-1
MS22520/1-01
MS3191-1
MS22520/1-01
MS3191-1
MS22520/1-01
MS3191-1
MS22520/1-01
MS3191-1
MS22520/1-01
MS3191-1
CBT600B or
CBT600
CBT600B or
CBT600
CBT600B or
CBT600
CBT600B or
CBT600
CBT600B
CBT600B
Crimp Tool
CONTACT RETAINING CLIP
FIGURE 1
CONTACT
When using the MS3191-1 (or CCT-1612) crimp tool with property locator, both the ceramic or formica
retaining ring for sizes 16 and 12 contacts must be removed. For sizes 8, 4, and 0 contacts, the
ceramic or formica retaining rings must be removed before crimping.
TH119 Turret
L16-3191-8
TH119 Turret
L16-3191-8
TH119 Turret
L16-3191-8
TH119 Turret
L16-3191-7
TH119 Turret
L16-3191-7
TH119 Turret
L12-3191-4
TH119 Turret
L12-3191-4
CCHP8
CCHP8
CCHP4
CCHP4
CCHP0-6
CCHP0-6
(CRIMP-ON
TERMINALS)
Locator
REAR
INSULATOR
Crimp Head†
CCH8-1
CCH8-1
CCH4-1
CCH4-1
CCH0-1
CCH0-1
-
-
-
-
-
-
-
5.
6.
7.
8.
9.
10. Slide endbell or junction shell down wire
INSERT
RETAINING
WASHER
Attach Formica retaining ring onto the con-
Assemble front insulator on engaging end of
Seat each contact securely in rear insulator.
Slide insulator assembly into hardware.
Slide washer and insulator retaining ring into
tact (see Figure 1).
contact.
place, making sure that insulator retaining is
fully seated in groove.
bundle and attach to shell (or barrel).
INSERT
RETAINING
RING
With Contact and Retaining Ring
16-Pin
8S-36
16 Pin*
8S-36
16 Socket
8S-16S
16 Socket
12-36
16 Socket*
12-36
12 Pin
12 Socket
8 Pin
8 Socket
4 Pin
4 Socket
0 Pin
0 Socket
Dimensions are shown in inches (millimeters).
MS-K Contacts Assembly Kit
Contact Size
STEEL ENDBELL
Dimensions subject to change.
www.ittcannon.com
Kit Part Number
320-0002-000
320-0001-000
320-0013-000
320-0005-000
320-0008-000
320-0009-000
320-0007-000
320-0010-000
320-0014-000
320-0011-000
320-0006-000
320-0012-000
320-0015-000
MS-K
205