SGM2358 sg-micro, SGM2358 Datasheet
SGM2358
Available stocks
Related parts for SGM2358
SGM2358 Summary of contents
Page 1
... It takes the minimum operating supply voltage down to 3V and the maximum recommended supply voltage is 5.5 V. SGM2358 is specified over the extended -40°C to +85°C temperature range. The amplifier in SGM2358 provides 1MHz bandwidth, Very low input bias currents of 10pA, these features enable SGM2358 to be used for integrators, photodiode amplifiers, and piezoelectric sensors ...
Page 2
... SGM2358 MIN / MAX mV MAX pA TYP pA TYP dB MIN dB MIN dB MIN µV/℃ TYP V TYP V TYP mA MIN V MIN V MAX dB MIN mA MAX MHz TYP V/µs TYP µs TYP µs TYP ...
Page 3
... ESD damage can range from subtle performance degradation to complete device failure. Precision 260℃ integrated circuits may be more susceptible to damage because very small parametric changes could .............................. 4000V cause specifications. 3 PACKAGE MARKING OPTION INFORMATION Tape and Reel, 2500 SGM2358YS the device not to meet SGM2358 its published ...
Page 4
... On Response vs.Frequency 0.2V IN P-P C =100pF 100kΩ 100 Frequency(KHz) Quiescent And Short-Circuit Current vs.Supply Voltage 2.5 3 3.5 4 4.5 Supply Voltage( 100pF 100KΩ L 1000 10000 5.5 SGM2358 ...
Page 5
... Input Voltage Noise Spectral Density vs.Frequency 10 0.01 0.1 1 Frequency(kHz) Open-Loop Gain vs.Temperature 150 140 R = 10kΩ 130 L 120 R = 2kΩ L 110 100 90 -40 - Temperature(℃) Power-Supply Rejection Ratio vs.Temperature 120 110 100 -40 - Temperature(℃) 10 100 SGM2358 ...
Page 6
... TYPICAL PERFORMANCE CHARACTERISTICS +25℃ +5V, and R = 100kΩ connected to Vs/2,unless otherwise noted Overload Recovery Time 2. 500mV IN 0V 500mV 0V Time(2µs/div) 6 SGM2358 ...
Page 7
... Power-Supply Bypassing and Layout The SGM2358 operates from either a single +3V to +5.5V supply or dual ±1.5V to ±2.75V supplies. For single-supply operation, bypass the power supply V capacitor which should be placed close to the V dual-supply operation, both the V be bypassed to ground with separate 0.1µ ...
Page 8
... Keep resistors value as low as possible and consistent with output loading consideration OUT R2 ½ V SGM2358 OUT R4 Vref / Make sure the filter is 2 8 ½ V SGM2358 Figure 6. Low Pass Active Filter SGM2358 OUT ...
Page 9
... A1 0.100 0.250 0.004 0.010 A2 1.350 1.550 0.053 0.061 B 0.330 0.510 0.013 0.020 C 0.190 0.250 0.007 0.010 D 4.780 5.000 0.188 0.197 E 3.800 4.000 0.150 0.157 E1 5.800 6.300 0.228 0.248 e 1.270TYP 0.050TYP L 0.400 1.270 0.016 0.050 θ 0° 8° 0° SGM2358 8° ...
Page 10
... SGMICRO is dedicated to provide high quality and high performance analog IC products to customers. All SGMICRO products meet the highest industry standards with strict and comprehensive test and quality control systems to achieve world-class consistency and reliability. For information regarding SGMICRO Corporation and its products, see www.sg-micro.com 10 Page SGM2358 ...