MCS0402 Vishay, MCS0402 Datasheet - Page 7

• Manufacturer Part Number: MCS0402
• Description: Precision Flat Chip Resistors
• Manufacturer: Vishay

MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision
Vishay Beyschlag
TEST AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
EN 60115-1, Generic specification (includes tests)
EN 140 400, Sectional specification (includes schedule for
qualification approval)
EN 140 401-801, Detail specification (includes schedule for
conformance inspection)
The components are approved in accordance with the
European CECC-system, where applicable. The following
table contains only the most important tests. For the full test
schedule refer to the documents listed above. The testing
also covers most of the requirements specified by
EIA/IS-703 and JIS-C-5202.
The tests are carried out in accordance with IEC 60068 and
under standard atmospheric conditions in accordance with
www.vishay.com
214
TEST PROCEDURES AND REQUIREMENTS
4.5
4.8.4.2
4.25.1
4.25.3
CLAUSE
60115-1
EN
METHOD
60068-2
TEST
IEC
−
−
-
-
-
70 °C: precision
operation mode
operation mode
upper category
Endurance at
Endurance at
Endurance at
Temperature
temperature
Resistance
coefficient
standard
70 °C:
TEST
For technical questions, contact: [e-mail]
whichever is the less severe;
whichever is the less severe;
Stability for product types:
At 20/- 10/20 °C and
1,5 h on; 0,5 h off
1.5 h on; 0.5 h off
1.5 h on; 0.5 h off
1.5 h on; 0.5 h off
U =
U =
PROCEDURE
Precision Flat Chip Resistors
125 °C; 1000 h
70 °C; 8000 h
70 °C; 8000 h
85 °C; 1000 h
70 °C; 1000 h
70 °C; 1000 h
20/85/20 °C
U = U
U = U
P
P
70
70
max.
max.
x R
x R
MCU 0805
MCA 1206
MCS 0402
MCT 0603
;
;
or
or
IEC 60068-1, 5.3. Climatic category LCT/UCT/56 (rated
temperature range: Lower Category Temperature, Upper
Category Temperature; damp heat, long term, 56 days) is
valid. Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
The components are mounted for testing on boards in
accordance with EN 60115-1, 4.31 unless otherwise
specified.
The parameters stated in the Test Procedures and
Requirements table are based on the required tests and
permitted limits of EN 140 401-801. However, some
additional tests and a number of improvements against those
minimum requirements have been included.
STABILITY CLASS 0.1
± (0.1 % R + 0.02 Ω)
± (0.2 % R + 0.02 Ω)
100 Ω to 47.5 kΩ
470 Ω to 10 kΩ
100 Ω to 10 kΩ
47 Ω to 332 kΩ
± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K
PERMISSIBLE CHANGE ΔR
± (0.4 % R + 0.05 Ω)
± (0.1 % R + 0.02 Ω)
± (0.2 % R + 0.02 Ω)
± (0.2 % R + 0.02 Ω)
± 0.1 % R; ± 0.25 % R
REQUIREMENTS
STABILITY CLASS 0.25
± (0.25 % R + 0.05 Ω)
± (0.2 % R + 0.02 Ω)
Document Number: 28700
> 47.5 kΩ to 1.5 MΩ
> 10 kΩ to 52.3 kΩ
> 10 kΩ to 511 kΩ
> 332 kΩ to 2 MΩ
39 Ω to < 100 Ω;
39 Ω to < 100 Ω;
39 Ω to < 47 Ω;
(1)
(1)
(1)
(1)
Revision: 16-Jul-08