VLA500K-01R Powerex, Inc., VLA500K-01R Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/5/538/powerex__inc__sml.jpg)
VLA500K-01R
Manufacturer Part Number
VLA500K-01R
Description
Hybrid Ic Igbt Gate Driver + Dc/dc Converter
Manufacturer
Powerex, Inc.
Datasheet
1.VLA500K-01R.pdf
(6 pages)
Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
VLA500K-01R
Hybrid IC IGBT Gate Driver +
DC/DC Converter
General Description
The VLA500K-01R is a hybrid integrated circuit designed
to provide gate drive for high power IGBT modules. This
circuit has been optimized for use with Powerex NF-
Series and A-Series IGBT modules. However, the
output characteristics are compatible with most MOS
gated power devices. The VLA500K-01R features a com-
pact single-in-line package design. The upright mount-
ing minimizes required printed circuit board space to
allow efficient and flexible layout. The VLA500K-01R
converts logic level control signals into fully isolated
+15V/-8V gate drive with up to 12A of peak drive current.
Isolated drive power is provided by a built in DC-to-DC
converter and control signal isolation is provided by an
integrated high speed opto-coupler. Short circuit protec-
tion is provided by means of destauration detection.
Short Circuit Protection
Figure 1 shows a block diagram of a typical desatura-
tion detector. In this circuit, a high voltage fast recovery
diode (D1) is connected to the IGBT’s collector to moni-
tor the collector to emitter voltage. When the IGBT is in
the off state, V
D1 off the (+) input of the comparator is pulled up to
the positive gate drive power supply (V+) which is nor-
mally +15V. When the IGBT turns on, the comparators
(+) input is pulled down by D1 to the IGBT’s V
The (-) input of the comparator is supplied with a fixed
voltage (V
comparator’s (+) input will be less than V
put will be low. During a normal off-state condition the
comparator’s (+) input will be larger than V
put will be high. If the IGBT turns on into a short circuit,
the high current will cause the IGBT’s collector-emitter
voltage to rise above V
IGBT is being driven on. This abnormal presence of
high V
called desaturation. Desaturation can be detected by
a logical AND of the driver’s input signal and the com-
parator output. When the output of the AND goes high
a short circuit is indicated. The output of the AND can
be used to command the IGBT to shut down in order
to protect it from the short circuit. A delay (t
provided after the comparator output to allow for the nor-
mal turn on time of the IGBT. The t
that the IGBT's V
during normal turn on switching. If t
erroneous desaturation detection will occur. The maxi-
Rev. 5/07
CE
when the IGBT is supposed to be on is often
trip
). During a normal on-state condition the
CE
is high and D1 is reverse biased. With
CE
has enough time to fall below V
trip
even though the gate of the
trip
trip
is set too short,
delay is set so
trip
trip
trip
and it’s out-
and it’s out-
) must be
CE(sat)
trip
.
mum allowable t
circuit withstanding capability. In typical applications
using Powerex IGBT modules the recommended limit is
10µs.
Operation of the VLA500K-01R
Desaturation Detector
The Powerex VLA500K-01R incorporates short circuit
protection using desaturation detection as described
above. A flow chart for the logical operation of the short-
circuit protection is shown in Figure 2. When a desatura-
tion is detected the hybrid gate driver performs a soft
shutdown of the IGBT and starts a timed (t
lock out. The soft turn-off helps to limit the transient
voltage that may be generated while interrupting the
large short circuit current flowing in the IGBT. During the
lock out the driver pulls Pin 28 low to indicate the fault
status. Normal operation of the driver will resume after
the lock-out time has expired and the control input signal
returns to its off state.
Adjustment of Trip Time
The VLA500K-01R has a default short-circuit detection
time delay (t
erroneous detection of short-circuit conditions as long
as the series gate resistance (R
mum recommended value for the module being used.
The 3µs delay is appropriate for most applications so
adjustment will not be necessary. However, in some low
frequency applications it may be desirable to use a
INPUT
Figure 1. Desaturation Detector
trip
AND
DELAY
) of approximately 3µs. This will prevent
t trip
trip
delay is limited by the IGBT’s short
DRIVE
GATE
COMPARE
SHUTDOWN
+
R G
G
V+
) is near the mini-
G
E
V trip
D1
IGBT
MODULE
timer
) 1.5ms
C
E
5