MPQ24S15-50C Wall Industries,Inc., MPQ24S15-50C Datasheet - Page 3

• Manufacturer Part Number: MPQ24S15-50C
• Description: 60 W Dc-dc Converter 10-36 Vdc Input 15 Vdc Output At 4.0 A Quarter-brick Package
• Manufacturer: Wall Industries,Inc.

Table 1: Pin Assignments
Figure 1: Mechanical Dimensions
Mechanical Dimensions (Heatsink Option - "HS" suffix)
(888) 597-WALL
INTERPRET DIMENSION AND TOLERANCE
NOTES:
1. PIN TO PIN TOLERANCE: ±.010 [±0.25] MEASURED AT STANDOFF FEATURE ONLY, DATUM-B.
2. PIN DIAMETER TOLERANCE OF : ±.005 [±0.13] MEASUREMENT READING APPLIES
3. UNLESS OTHERWISE SPECIFIED.
4. THERMAL TRANSFER PLATE MATERIAL: .040 [1.02] THICK, ALUMINUM ALLOY 3003-0,
.XX=±.02[0.5] .XXX=±.010[0.25]
THIRD ANGLE PROJECTION
PIN DESIGNATION
DO NOT SCALE DRAWING
TO AREA FROM INTERFACE-PLANE SURFACE DATUM-C TO END OF PIN ONLY.
PER: QQA 250/2 WITH BLACK SOFT SULFURIC ANODIZE FINISH.
UNLESS OTHERWISE SPECIFIED
INTERPRET DIMENSION AND TOLERANCE
WALL INDUSTRIES, INC.
.XX=±.02[0.5] .XXX=±.010[0.25]
THIRD ANGLE PROJECTION
1
2
3
4
5
6
7
8
Unit: inches [mm]
Unit: inches [mm]
DO NOT SCALE DRAWING
Pin #
PER ASME Y14.5M - 1994
ALL DIMENSONS ARE IN INCHES
1
2
3
4
5
6
7
8
[ XX ] ARE IN MILLIMETERS
PER ASME Y14.5M - 1994
ANGLES
APPLIED TOLERANCES:
+SENSE
+Vin
ON/OFF
-Vin
+Vout
TRIM
-SENSE
-Vout
ANGLES= ±1°
.47 [11.9]
±1
PIN Ø
Ø.062 [1.57]
Ø.040 [1.02]
Ø.062 [1.57]
Ø.062 [1.57]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.062 [1.57]
+Vin
Enable
-Vin
+Vout
+SENSE
TRIM
-SENSE
-Vout
RECOMMENDED FINISHED RECEIVING PCB
STAND-OFF HOLE Ø.052±.003 [1.32±0.08]
Pin Name
1
2
3
.00 [0.0]
.005
Ø.040 [1.02] PINS ONLY 6X
STANDOFF DIMENSION
MAX SCREW DEPTH .100 FROM SURFACE-A 4X
.071±.005 [1.80±0.13]
C
LABEL
.26 [6.5]
DOT DENOTES
PIN-1
Positive Input
Remote On/Off
Negative Input
Negative Output
Negative Remote Sense
Output Voltage Trim
Positive Remote Sense
Positive Output
A
TORQUE: 6.0 lbf in [ 0.68 N m]
MAX APPLIED RECIEVING
1
2
3
.112(NO:4)-40UNC-2B 4X
.47 [11.9]
1.860 [47.24]
Function
2.00 [50.8]
2.37 [60.2]
RECOMMENDED FINISHED RECEIVING PCB
STAND-OFF HOLE Ø.052±.003 [1.32±0.08]
1
2
3
.19 [4.7]
PIN-2 SHOWN FOR DIMENSIONS
Ø.040 [1.02] PINS ONLY 4X
STANDOFF DIMENSION
MAX SCREW DEPTH .100 FROM SURFACE-A 4X
.071±.005 [1.80±0.13]
www.wallindustries.com
.00 [0.0]
.26 [6.5]
.005
4
5
6
7
8
1.030 [26.16]
LABEL
DOT DENOTES
PIN-1
.19 [4.7]
PIN END
.20 MIN [5.1 MIN]
SEE NOTE-4
SEE NOTE-3
PIN LENGTH FROM
INTERFACE-PLANE ONLY
TORQUE: 6.0 lbf in [ 0.68 N m]
C
.00 [0.0]
1
2
3
MAX APPLIED RECIEVING
If not used, leave open for standard unit, short to –Vin on ‘R’ units.
If not used, short to –Vo.
If not used, leave open.
If not used, short to +Vo.
.51 [13.0]
.112(NO:4)-40UNC-2B 4X
B
SEE NOTE-4
INTERFACE-PLANE
-A-
Rev. C
1.860 [47.24]
2.00 [50.8]
2.37 [60.2]
4
5
6
7
8
.19 [4.7]
NOTES:
1. PIN TO PIN TOLERANCE: ±.010 [±0.25] MEASURED AT STANDOFF FEATURE ONLY, DATUM-B.
2. PIN DIAMETER TOLERANCE OF : ±.005 [±0.13] MEASUREMENT READING APPLIES
3. STANDARD PIN LENGTH UNLESS OTHERWISE SPECIFIED.
4. THERMAL TRANSFER PLATE MATERIAL: .040 [1.02] THICK, ALUMINUM ALLOY 3003-0,
TO AREA FROM INTERFACE-PLANE SURFACE DATUM-C TO END OF PIN ONLY.
PER: QQA 250/2 WITH BLACK SOFT SULFURIC ANODIZE FINISH.
4
5
6
7
8
PIN DESIGNATION
.19 [4.7]
1
2
3
4
5
6
7
8
TECHNICAL DATASHEET
PIN END
.47 [11.9]
.20 MIN [5.1 MIN]
SEE NOTE-3
PIN LENGTH FROM
INTERFACE-PLANE ONLY
.51 [13.0]
Comments
.00 [0.0]
+SENSE
+Vin
ON/OFF
-Vin
+Vout
-SENSE
-Vout
TRIM
B
4
5
6
7
8
MPQ24S15-50C
-A-
INTERFACE-PLANE
PIN Ø
Ø.040 [1.02]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.062 [1.57]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.062 [1.57]
4
5
6
7
8
Page 3 of 11
.47 [11.9]
1
2
3