APL5912 Anpec Electronics, APL5912 Datasheet
APL5912
Available stocks
Related parts for APL5912
APL5912 Summary of contents
Page 1
... Copyright ANPEC Electronics Corp. Rev. A.6 - Jun., 2005 General Description The APL5912 ultra low dropout linear regulator. This product is specifically designed to provide well supply voltage for front-side-bus termination on motherboard and NB applications. The IC needs two supply voltages, a control voltage for the circuitry and a main supply volatege for power conversion, to reduce power dissipation and provide extremely low dropout ...
Page 2
... Ordering and Marking Information APL5912 - www.DataSheet4U.com APL5912 KA : Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS and compatible with both SnPb and lead-free soldiering operations. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J STD-020C for MSL classification at lead-free peak reflow temperature ...
Page 3
... Soldering Temperature, 10 Seconds SDR V Minimum ESD Rating (Human Body Mode) ESD Copyright ANPEC Electronics Corp. Rev. A.6 - Jun., 2005 R4 C CNTL 10 (in the range of 5.1~15 ) 1uF R3 VCNTL VIN POK 3 VOUT 4 VOUT APL5912 GND R2 78k V ( OUT 1.05 43 137.6 1.5 27 30.86 1.8 15 Parameter 3 V ...
Page 4
... V =3.3 5% CNTL 0 =5.0 5% CNTL = 5V, V CNTL = Test Conditions EN = VCNTL EN = GND V Rising CNTL V Rising IN 4 Value Unit o 40 C/W Range Unit 3 1.1 ~ 3.3 V 0.8 ~ 1 -25 ~ 125 C = 1.5V 1.2V and OUT A APL5912 Unit Min Typ Max 0 180 300 A 2.7 2.9 3.1 V 0.4 V 0.8 0.9 1.0 V 0.5 V www.anpec.com.tw ...
Page 5
... T = -25 ~ 125 C CNTL =3.3V CNTL =3.3V -25 ~ 125 C CNTL J T Rising J V Falling FB Rising EN EN=GND V Rising FB V Falling FB POK sinks 5mA 5 = 1.2V and OUT A APL5912 Unit Min Typ Max 0.8 V -1.5 +1.5 % 0.06 0.15 % 0.06 0.15 % 0.15 0 6.8 7.8 8 150 0.4 V 0.3 ...
Page 6
... APL5912 Typical Operating Characteristics VCNTL Supply Current vs. Junction Temperature 1.0 0.9 =5V V CNTL 0.8 www.DataSheet4U.com 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -50 -25 0 Junction Temperature ( C) Dropout Voltage vs. Output Current 250 =3.3V V CNTL V =1.2V OUT 200 150 100 Output Current, l Copyright ANPEC Electronics Corp. Rev. A.6 - Jun., 2005 =3.3V V CNTL 100 125 =125 C ...
Page 7
... APL5912 Typical Operating Characteristics Reference Voltage vs. Junction Temperature 0.808 0.806 www.DataSheet4U.com 0.804 0.802 0.800 0.798 0.796 0.794 0.792 -50 -25 Junction Temperature ( C) 0. 4.5V~5.5V CNTL 1.2V -10.00 OUT OUT C = 100 330uF(ESR=30m ) -20.00 OUT -30.00 -40.00 -50.00 -60.00 -70.00 100 1000 Copyright ANPEC Electronics Corp. Rev. A.6 - Jun., 2005 0 25 ...
Page 8
... APL5912 Operating Waveforms Test Circuit www.DataSheet4U.com Load transient Response Using an Output Capacitor with ESR 18m 1 ...
Page 9
... APL5912 Operating Waveforms (Cont.) Using an MLCC as the Output Capacitor 1 F/6.3V (ESR = OUT - I = 10mA 10mA, Rise time = Fall time = 1 S OUT I = 10mA -> 5A www.DataSheet4U.com OUT Ch1 : V , 100mV/Div OUT Ch2 : I , 2A/Div OUT Time : 2 S/Div 2. Power ON / Power OFF : - V = 1.5V 220 F/6.3V (ESR = 30m ...
Page 10
... APL5912 Operating Waveforms (Cont.) 3. Shutdown and Enable : - V = 1.5V 220 F/6.3V (ESR = 30m OUT www.DataSheet4U.com Ch1 Ch1 Ch2 Ch2 Ch3 Ch3 Ch4 Ch4 Ch1 : V ,5V/div EN Ch2 : V ,1V/div OUT Ch3 : I ,1A/div OUT Ch4 : V ,1V/div POK Time : 1ms/div 4. POK Delay : - V = 1.5V 220 F/6.3V (ESR = 30m ...
Page 11
... APL5912 Functional Pin Description GND (Pin 1) Ground pin of the circuitry. All voltage levels are measured with respect to this pin. FB (Pin 2) www.DataSheet4U.com Connecting this pin to an external resistor divider receives the feedback voltage of the regulator. The output voltage set by the resistor divider is determined ...
Page 12
... APL5912 from damages during overload or short- circuit conditions. Under-Voltage Protection (UVP) The APL5912 monitors the voltage on FB pin after soft- start process is finished. Therefore the UVP is disable during soft-start. When the voltage on FB pin falls below the under-voltage threshold, the UVP circuit shuts off the output immediately ...
Page 13
... During load transients, the output capacitors, depending on the stepping amplitude and slew rate of load current, are used to reduce the slew rate of the current seen by the APL5912 and help the device to minimize the variations of output voltage for good transient response. For the applications with large stepping load current, the low-ESR bulk capacitors are normally recommended ...
Page 14
... Connect the one pin the Pin 3 of APL5912 - Connect the one pin the Pin 3 of APL5912 14 on the PCB. The main current flow is through the exposed pad. The role of VIN is a voltage sense. Refer Figure 3 to make a proximate topology. ...
Page 15
... APL5912 Application Information (Cont.) Thermal Considerations See Figure 3. The SOP-8 cost-effective package featuring a small size like a standard SOP-8 and a bottom exposed pad to minimize the thermal resistance of the package, being applicable to high current www.DataSheet4U.com applications. The exposed pad must be soldered to the top V plane ...
Page 16
... APL5912 Packaging Information SOP-8-P pin ( Reference JEDEC Registration MS-012) www.DataSheet4U.com e1 Dim Copyright ANPEC Electronics Corp. Rev. A.6 - Jun., 2005 0.004max 1.35 1. 4.80 5.00 3.00R E F 3.80 4.00 2.60R ...
Page 17
... APL5912 Physical Specifications Terminal Material Lead Solderability Reflow Condition www.DataSheet4U.com Tsmax Tsmin 25 Classificatin Reflow Profiles Profile Feature Average ramp-up rate ( Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Time maintained above: - Temperature ( Time ( Peak/Classificatioon Temperature (Tp) ...
Page 18
... APL5912 Classificatin Reflow Profiles(Cont.) Table 1. SnPb Entectic Process – Package Peak Reflow Temperature s Package Thickness <2.5 mm 2.5 mm www.DataSheet4U.com Table 2. Pb-free Process – Package Classification Reflow Temperatures Package Thickness <1.6 mm 1.6 mm – 2.5 mm 2.5 mm *Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature (this means Peak reflow temperature +0 C. ...
Page 19
... APL5912 Carrier Tape(Cont.) www.DataSheet4U.com Application A 330 1 SOP- 8/-P F 5.5 1 Cover Tape Dimensions Application SOP- 8/-P Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R ...
Page 20
www.DataSheet4U.com ...