CT2100-400 Aeroflex Circuit Technology, CT2100-400 Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
CT2100-400
Manufacturer Part Number
CT2100-400
Description
MICROPROCESSOR CONTROLLED QUAD SOLID STATE RELAY
Manufacturer
Aeroflex Circuit Technology
Datasheet
1.CT2100-400.pdf
(6 pages)
www.DataSheet.co.kr
The CT2100-400 is a quad solid
state relay. The device has been
designed to provide an interface
which
computer I/O port. The switches
are controlled by a single data
word which the processor writes to
an
addition
function ON/OFF and Trip flags
provide the operational status of
each of the four switches. These
signals are internally contained in
an 8 bit status register which is
accessible
command. The switches may also
be
(without write strobes) by use of
separate initialization pins. These
may also be used for Power-Up
control in a microprocessor based
system.
Aeroflex Circuit Technology
internal
controlled
SWITCH CONTROL
Supply Voltage (V
Supply Voltage (V
Logic Input Voltage — Pins 2-9, 12-19
Switch Point Voltage — Pins 39-40, 29-32, 21-22
Storage Temperature Range
operates
Supply Voltage (V
Supply Voltage (V
Logic Input Maximum Voltage (High) — Pins 2-9, 12-19
Logic Input Minimum Voltage (Low) — Pins 2-9, 12-19
Switch Point Voltage — Pins 39-40, 29-32, 21-22
Operating Temperature Range
DESCRIPTION
to
by
the
control
an
asynchronously
as
basic
CC
EE
CC
EE
I/O
a
latch.
) — Pin 1
) — Pin 20
) — Pin 1
) — Pin 20
simple
switch
Table 2 — Recommended Operating Conditions
read
In
Table 1 — Absolute Maximum Ratings
The
independent
switches which may be used as
high side or low side drivers. The
isolated design allows the user
to parallel devices or place them
in series as required for the
specific application. Control of
the switch is via I/O write
(Address 0) or asynchronous
control lines. The CT2100-400
has an internal switch control
latch which is updated via
subsystem
illustrated in Figure 2. Once the
I/O write is completed the switch
is latched into the OFF or ON
state. The switch may also be
controlled
PRESET and CLEAR lines.
These
drive the switch control latch
without the need for a write
CT2100-400
lines
2
I/O
via
-0.5 to +7.0 Volts DC
-.5 to +18 Volts DC
-0.5 to V
-600 to +600 Volts (200 ns)
80 Volts DC
-65°C to +150 °C
fully
asynchronously
write
has
CC
individual
isolated
+.5 Volts DC
+5.0 VDC ±10%
+14.25 to +15.75 VDC
+3.3 V
+0.8 V
60 VDC
-55°C to +125 °C
four
as
SCDCT2100 REV B 10/1/98 Plainview NY (516) 694-6700
strobe. The PRESET/CLEAR
inputs
initialize pin.
Each switch in the CT2100-400
is monitored for circuit Trip and
ON/OFF. This data is contained
in a 8 bit status register which is
accessible via an I/O read
(Address 0)
timing for the I/O read is shown
in Figure 1. The Trip and
ON/OFF flags are provided to
the
operational capability of the
switch versus the status of the
controlled load. The Trip bit is
set high when the switch has
conducted between 1.1 to 3
amps of current based on the
time to trip curve in Figure 3.
The over current DC trip point is
typically 1.3 amps.
system
SWITCH STATUS
are
enabled
command.
to
assess
by
The
the
the
Datasheet pdf - http://www.DataSheet4U.net/