CM6807BGR Champion Microelectronic, CM6807BGR Datasheet - Page 11

no-image

CM6807BGR

Manufacturer Part Number
CM6807BGR
Description
10-pin Green-mode Pfc/pwm Combo Controller for High Density AC Adapter
Manufacturer
Champion Microelectronic
Datasheet
The I
I
R
than 5mV. Usually, we design the pole of I
fpfc/6, one sixth of the PFC switching frequency. Therefore,
the boost inductor can be reduced 6 times without
disturbing the stability. Therefore, the capacitor of the I
Filter, C
IAC, R
and light load, and Startup current
There are 4 purposes for IAC pin:
Start Up of the system, UVLO, VREFOK and Soft Start
During the Start-up period, R
up current~100uA from the rectified line voltage to IAC pin.
Inside of CM6807A during the start-up period, IAC is
connected to VCC until the VCC reaches UVLO voltage
which is 13V (UVB) and internal reference voltage is stable,
it will disconnect itself from VCC. During the Start up, the
soft start function is triggered and the duration of the soft
start will last around 10mS.
PFC section wakes up after Start up period
After Start up period, PFC section will softly start since
VEAO is zero before the start-up period. Since VEAO is a
slew rate enhanced transconductance amplifier (see figure
3), VEAO has a high impedance output like a current
source and it will slowly charge the compensation net work
which needs to be designed by using the voltage loop gain
equation.
Before PFC boost output reaches its design voltage, it is
around 380V and VFB reaches 2.5V, PWM section is off.
2006/10/11 Rev1.0
SENSE
FILTER
1.) For the leading edge modulation, when the duty
2.) During the startup period, Rac also provides the
3.) Since IAC pin with R
4.) It also will try to keep the maximum input power to
SENSE
Filter is between 100 ohm and 50 ohm. By selecting
AC
equal to 50 ohm will keep the offset of the IEAO less
FILTER
, Automatic Slope Compensation, DCM at high line
cycle is less than 50%, it requires the similar slope
compensation, as the duty cycle of the trailing
edge modulation is greater than 50%.
CM6807A, it is a relatively easy thing to design.
Use an more than 2KK ohm resistor, R
connect IAC pin and the rectified line voltage. It
will do the automatic slope compensation. If the
input boost inductor is too small, the R
need to be reduced more.
initial startup current, 100uA;therefore, the bleed
resistor is not needed.
signal, it also enhances the signal to noise ratio
and the THD of the input current.
be constant. However, the maximum input power
will still go up when the input line voltage goes up.
Filter is a RC filter. The resistor value of the
, will be around 283nF.
AC
AC
resistor will provide the start
behaves as a feedforward
10-PIN Green-Mode PFC/PWM Combo CONTROLLER for High Density AC Adapte
Champion Microelectronic Corporation
SENSE
Filter at
AC
In the
AC
SENSE
may
to
PWM section wakes up after PFC reaches steady state
PWM section is off all the time before PFC VFB reaches
2.45V. Then internal 10mS digital PWM soft start circuit
slowly ramps up the soft-start voltage.
PFC OVP Comparator
PFC OVP Comparator sense VFB pin which is the same the
voltage loop input. The good thing is the compensation
network is connected to VEAO. The PFC OVP function is a
relative fast OVP. It is not like the conventional error amplifier
which is an operational amplifier and it requires a local
feedback and it make the OVP action becomes very slow.
The threshold of the PFC OVP is 2.5V+10% =2.75V with
250mV hysteresis.
PFC Tri-Fault Detect Comparator
To
component count, and simplify compliance to UL1950 safety
standards, the CM6807A includes PFC Tri-Fault Detect. This
feature monitors VFB (Pin 5) for certain PFC fault conditions.
In case of a feedback path failure, the output of the PFC
could go out of safe operating limits. With such a failure, VFB
will go outside of its normal operating area. Should VFB go
too low, too high, or open, PFC Tri-Fault Detect senses the
error and terminates the PFC output drive.
PFC Tri-Fault detect is an entirely internal circuit. It requires
no external components to serve its protective function.
VCC OVP and generate VCC
For the CM6807A system, if VCC is generated from a source
that is proportional to the PFC output voltage and once that
source reaches 17.9V, PFCOUT, PFC driver will be off.
The VCC OVP resets once the VCC discharges below
16.4V, PFC output driver is enabled. It serves as redundant
PFC OVP function.
Typically, there is a bootstrap winding off the boost inductor.
The VCC OVP comparator senses when this voltage
exceeds 17.9V, and terminates the PFC output drive. Once
the VCC rail has decreased to below 16.4V the PFC output
drive be enabled. Given that 16V on VCC corresponds to
380V on the PFC output, 17.9V on VCC corresponds to an
OVP level of 460V.
It is a necessary to put RC filter between bootstrap winding
and VCC. For VCC=15V, it is sufficient to drive either a
power MOSFET or a IGBT.
improve
power
supply
CM6807(A;B;C)
reliability,
reduce
Page 11
system
r

Related parts for CM6807BGR