LM392H National Semiconductor Corporation, LM392H Datasheet - Page 3

• Manufacturer Part Number: LM392H
• Description: LM392 - Low Power Operational Amplifier/voltage Comparator, Package: Soic Narrow, Pin Nb=8
• Manufacturer: National Semiconductor Corporation

OP AMP ONLY
Large Signal Voltage Gain
Input Offset Current Drift
Output Voltage Swing
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Output Current Source
Output Current Sink
Input Offset Voltage Drift
COMPARATOR ONLY
Voltage Gain
Large Signal Response Time
Response Time
Output Sink Current
Saturation Voltage
Output Leakage Current
Electrical Characteristics
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Note 2: For operating at temperatures above 25˚C, the LM392 must be derated based on a 125˚C maximum junction temperature and a thermal resistance of
122˚C/W which applies for the device soldered in a printed circuit board, operating in still air ambient. The dissipation is the total of both amplifiers — use external
resistors, where possible, to allow the amplifier to saturate or to reduce the power which is dissipated in the integrated circuit.
Note 3: Short circuits from the output to V
current is approximately 40 mA for the op amp and 30 mA for the comparator independent of the magnitude of V
continuous short circuits can exceed the power dissipation ratings and cause eventual destruction.
Note 4: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action
on the IC chip. This transistor action can cause the output voltages of the amplifiers to go to the V
duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns
to a value greater than −0.3V (at 25˚C).
Note 5: These specifications apply for V
Note 6: At output switch point, V
Note 7: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the input lines.
Note 8: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode
voltage range is V
Note 9: Due to proximity of external components, insure that coupling is not originating via the stray capacitance between these external parts. This typically can
be detected as this type of capacitive coupling increases at higher frequencies.
Note 10: Positive excursions of input voltage may exceed the power supply level. As long as the other input voltage remains within the common-mode range, the
comparator will provide a proper output state. The input voltage to the op amp should not exceed the power supply level. The input voltage state must not be less
than −0.3V (or 0.3V below the magnitude of the negative power supply, if used) on either amplifier.
Note 11: The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained.
(V
+
= 5 V
DC
Parameter
; specifications apply to both amplifiers unless otherwise stated) (Note 5)
+
− 1.5V, but either or both inputs can go to 32V without damage.
O
. 1.4V, R
+
+
= 5V, unless otherwise stated. For the LM392, temperature specifications are limited to 0˚C
can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output
S
= 0
V
R
R
DC, T
V
DC, T
V
V
V
V
V
V
R
R
R
V
V
V
V
V
V
I
V
I
V
V
V
V
SINK
SINK
+
DC
IN(+)
+
IN(−)
+
IN(−)
+
IN
RL
RL
IN(−)
O
IN(−)
IN(−)
IN(−)
o
IN(−)
o
with V
L
L
S
S
L
(Continued)
= 5 V
= 30 V
= 15 V
= 2 k , T
= 2 k , T
= 15 V
= 15 V
= 15 V
= 0
= 0
= TTL Logic Swing, V
= 5 V
= 5 V
1.5 V
15 k , V
A
A
= 1 V
= 1 V
= 1 V
=1 V
= 0, V
= 0, V
+
4 mA, T
4 mA
from 5V to 30V; and over the full input common-mode range (0V to V
= 25˚C, V
= 25˚C
1 V
1 V
DC
DC
DC
DC
DC
DC
DC
DC
DC
DC
, T
DC
DC
DC
DC
DC
IN(+)
IN(+)
, V
, V
, V
, V
, R
, R
, T
A
A
, V
, V
, V
+
A
, V
, V
, V
= 25˚C
= 25˚C
A
A
o
o
o
o
L
L
Conditions
= 15 V
= 25˚C
IN(+)
IN(+)
IN(+)
swing = 1 V
IN(−)
IN(+)
IN(+)
= 2 V
=2V
=200 mV, T
= 5.1 k , T
= 5.1 k , T
= 25˚C
= 25˚C
CM
1 V
1 V
= 0, V
= 0 V
DC
= 0,
= 0,
= 0 V
= 0 V
= 0 V
3
DC
DC
DC
DC
, T
,
,
, T
, T
REF
DC
A
DC
DC
DC
DC
A
A
= 25˚C
A
A
A
DC
,
to V
= 25˚C
,
= 25˚C
,
,
= 1.4 V
= 25˚C
= 25˚C
= 25˚C
to 11 V
+
−1.5
+
DC
voltage level (or to ground for a large overdrive) for the time
DC
,
Min
+
25
65
65
20
10
12
50
. At values of supply voltage in excess of 15V,
0
6
LM392
Typ
100
100
200
300
250
1.3
0.1
70
40
20
50
10
16
7
+
− 1.5V).
V
T
Max
A
+
400
700
1.0
−1.5
+70˚C.
www.national.com
nA
µA
pA
Units
µV/˚C
V/mV
V/mV
mA
mA
mA
mV
mV
dB
dB
µA
DC
ns
µs
V
/˚C