MAX5023 Maxim, MAX5023 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
MAX5023
Manufacturer Part Number
MAX5023
Description
65V / Low-Quiescent-Current / High-Voltage Linear Regulators with P Reset and Watchdog Timer
Manufacturer
Maxim
Datasheet
1.MAX5023.pdf
(13 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX5023LASA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX5023LASA+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX5023LASA+T
Manufacturer:
MAXIM
Quantity:
175
Part Number:
MAX5023MASA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX5023MASA+T
Manufacturer:
MAXIM
Quantity:
97
Part Number:
MAX5023TASA
Manufacturer:
MAXIM/美信
Quantity:
20 000
65V, Low-Quiescent-Current, High-Voltage Linear
Regulators with µP Reset and Watchdog Timer
Figure 2. Watchdog Operation Timing Diagram
The reset supervisor circuit is fully integrated in the
MAX5023/MAX5024 and uses the same reference volt-
age as the regulator. RESET asserts during power-
up/down and brownout conditions. RESET goes low if
V
and remains low for 200ms (reset timeout period, t
after V
the MAX5023 only, RESET also asserts when WDI does
not transition for 1.6s (watchdog timeout period, t
Two supply tolerance reset thresholds, -7.5% and
-12.5%, are available for each device type.
A watchdog timer asserts RESET if the watchdog input
(WDI) is not toggled for 1.6s (watchdog timeout period,
t
od, t
periods of time, the reset output appears as a pulse
train, asserted for 200ms, deasserted for 1.6s, until WDI
is toggled again. Once RESET asserts, it stays low for
the entire reset timeout period ignoring any WDI transi-
tions during the reset timeout period.
8
WD
V
HIGH AND EN = HIGH
V
LOW AND EN = HIGH
OUT
OUT
OUT
_______________________________________________________________________________________
). RESET remains low for 200ms (reset timeout peri-
WHEN WATCHDOG IS HELD
WHEN WATCHDOG IS HELD
RP
drops below the preset output voltage threshold,
OUT
). If the watchdog is not updated for lengthy
rises above the reset voltage threshold. For
Watchdog Timer (MAX5023 only)
RESET
RESET
V
V
WDI
WDI
OUT
OUT
V
V
EN
EN
IN
IN
OV
OV
OV
OV
OV
OV
BATT
BATT
BATT
BATT
POR
POR
Reset Output
NORMAL OPERATION
NORMAL OPERATION
WD
RP
).
)
Figure 2 shows the Watchdog Operation Timing
Diagram. To prevent the watchdog from asserting
RESET, toggle WDI with a valid rising or falling edge
prior to t
when WDI toggles prior to t
The watchdog resumes counting after RESET deasserts.
The MAX5023/MAX5024 support two logic inputs, EN
(active high) and HOLD (active low), making these
devices “automotive friendly.” For example, the ignition
drives EN high, the regulator turns on and remains on
even if EN goes low, as long as HOLD is forced low
and stays low after initial regulator power-up. This fea-
ture makes it possible to implement a self-holding
circuit without external components. Release HOLD (an
internal current source connects HOLD to OUT) to turn
the regulator off.
Force EN low and HOLD high to place the MAX5023/
MAX5024 into shutdown mode. Shutdown mode draws
less than 16µA of supply current. Table 1 shows the state
of the regulator output with respect to the voltage level at
WD
(min) = 1.12s. The watchdog counter clears
WDI HELD HIGH
WDI HELD LOW
Enable and Hold Inputs
WD
or when RESET asserts.