MAX6955 Maxim, MAX6955 Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
MAX6955
Manufacturer Part Number
MAX6955
Description
2-Wire Interfaced / 2.7V to 5.5V LED Display Driver with I/O Expander and Key Scan
Manufacturer
Maxim
Datasheet
1.MAX6955.pdf
(39 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX6955AAX
Manufacturer:
IDT
Quantity:
14
Company:
Part Number:
MAX6955AAX+
Manufacturer:
Maxim
Quantity:
481
Company:
Part Number:
MAX6955AAX+T
Manufacturer:
Maxim
Quantity:
114
Company:
Part Number:
MAX6955ATL+
Manufacturer:
MAXIM
Quantity:
2 672
Company:
Part Number:
MAX6955ATL+T
Manufacturer:
MINDSPEE
Quantity:
4 500
The Key_A debounced, Key_B debounced, Key_C
debounced, and Key_D debounced read-only registers
(Table 35) show which keys have been detected as
debounced by the key-scanning circuit.
Each bit in the register corresponds to one key switch.
The bit is set if the switch has been correctly
debounced since the register was read last. Reading a
debounced register clears that register (after the data
has been read) so that future keys pressed can be
identified. If the debounced registers are not read, the
key-scan data accumulates. However, as there is no
FIFO in the MAX6955, the user is not able to determine
key order, or whether a key has been pressed more
than once, unless the debounced key status registers
are read after each interrupt, and before the next key-
scan cycle.
Reading any of the four debounced registers clears the
IRQ output. If a key is pressed and held down, the key is
reported as debounced (and IRQ issued) only once. The
key must be detected as released by the key-scanning
circuit, before it debounces again. If the debounced reg-
isters are being read in response to the IRQ being
asserted, then the user should generally read all four
registers to ensure that all the keys that were detected by
the key-scanning circuit are discovered.
The Key_A pressed, Key_B pressed, Key_C pressed,
and Key_D pressed read-only registers (Table 36)
show which keys have been detected as pressed by
the key-scanning circuit during the last test.
Each bit in the register corresponds to one key switch.
The bit is set if the switch has been detected as
pressed by the key-scanning circuit during the last test.
The bit is cleared if the switch has not been detected
as pressed by the key-scanning circuit during the last
test. Reading a pressed register does not clear that
register or clear the IRQ output.
The display test register (Table 37) operates in two
modes: normal and display test. Display test mode
turns all LEDs on (including DPs) by overriding, but not
altering, all controls and digit registers (including the
shutdown register), except for the digit-type register
and the GPIO configuration register. The duty cycle,
while in display test mode, is 7/16 (see the Choosing
Supply Voltage to Minimize Power Dissipation section).
2-Wire Interfaced, 2.7V to 5.5V LED Display
______________________________________________________________________________________
Driver with I/O Expander and Key Scan
Key Debounced Registers
Display Test Register
Key Pressed Registers
The RC oscillator uses an external resistor, R
an external capacitor, C
The allowed range of f
sets the peak segment current. The recommended val-
ues of R
makes the blink frequencies selectable between 0.5Hz
and 1Hz. The recommended value of R
peak current to 40mA, which makes the segment cur-
rent adjustable from 2.5mA to 37.5mA in 2.5mA steps.
where:
K
K
R
C
C
pF, typically 2pF
The recommended value of R
ommended value of C
The recommended value of R
allowed value, since it sets the display driver to the
maximum allowed peak segment current. R
set to a higher value to set the segment current to a
lower peak value where desired. The user must also
ensure that the peak current specifications of the LEDs
connected to the driver are not exceeded.
The effective value of C
external capacitor used, but also the stray capacitance
from OSC to GND. This capacitance is usually in the
1pF to 5pF range, depending on the layout used.
Bicolor digits group a red and a green die together for
each display element, so that the element can be lit red
or green (or orange), depending on which die (or both)
is lit. The MAX6955 allows each segment’s current to
be set individually from the 1/16th (minimum current
and LED intensity) to 15/16th (maximum current and
LED intensity), as well as off (zero current). Thus, a
bicolor (red-green) segment pair can be set to 256
color/intensity combinations.
L
F
SET
SET
STRAY
Selecting External Components R
= 2240
= 5376
= external resistor in kΩ
= external capacitor in pF
C
SET
= stray capacitance from OSC pin to GND in
SET
f
and C
OSC
to Set Oscillator Frequency and
Applications Information
I
= K
SEG
SET
F
SET
OSC
= K
set the oscillator to 4MHz, which
/ (R
SET
SET
is 22pF.
L
Peak Segment Current
SET
is 1MHz to 8MHz. R
, to set the frequency, f
/ R
includes not only the actual
Driving Bicolor LEDs
SET
x C
SET
SET
SET
is 56kΩ and the rec-
mA
) MHz
is the minimum
SET
also sets the
SET
SET
SET
SET
can be
, and
and
OSC
also
19
.