MAX9768 Maxim Integrated Products, MAX9768 Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX9768
Manufacturer Part Number
MAX9768
Description
10W Mono Class D Speaker Amplifier
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX9768.pdf
(25 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX9768BETG+
Manufacturer:
Maxim Integrated Products
Quantity:
32 336
Part Number:
MAX9768BETG+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX9768ETG+
Manufacturer:
MAXIM
Quantity:
1 000
Part Number:
MAX9768ETG+
Manufacturer:
MAXIM/美信
Quantity:
20 000
www.datasheet4u.com
Table 2. Modulation Scheme Selection In Analog Mode
10W Mono Class D Speaker
Amplifier with Volume Control
The MAX9768 features two output modulation
schemes: filterless modulation or classic PWM, selec-
table through SCLK when the device is in analog mode
(ADDR2 and ADDR1 = GND, Table 2) or through the
I
lation scheme eliminates the LC filter required by tradi-
tional Class D amplifiers, reducing component count,
conserving board space and system cost. Although the
MAX9768 meets FCC and other EMI limits with a low-
cost ferrite bead filter, many applications still may want
to use a full LC-filtered output. If using a full LC filter,
the performance is best with the MAX9768 configured
for classic PWM output.
Switching between schemes while in normal operating
mode with the I
pop protected. To have click-and-pop protection when
switching between output schemes, the device must
enter shutdown mode and be configured to the new out-
put scheme before the startup sequence is terminated.
The startup time for the MAX9768 is typically 220ms.
The startup time for the MAX9768B is typically 15ms.
Efficiency of a Class D amplifier is due to the switching
operation of the output stage transistors. In a Class D
amplifier, the output transistors act as current-steering
switches and consume negligible additional power.
Any power loss associated with the Class D output
stage is mostly due to the I
resistance, and quiescent-current overhead.
The theoretical best efficiency of a linear amplifier is
78%, however, that efficiency is only exhibited at peak
output power. Under normal operating levels (typical
music reproduction levels), efficiency falls below 30%,
whereas the MAX9768 still exhibits > 80% efficiencies
under the same conditions (Figure 2).
14
2
C interface (Table 7). Maxim’s unique, filterless modu-
ADDR2
______________________________________________________________________________________
0
0
Filterless Modulation/PWM Modulation
2
ADDR1
C interface, the output is not click-and-
0
0
2
R loss of the MOSFET on-
Analog Volume Control
Analog Volume Control
SDA/VOL
Efficiency
When the output current exceeds the soft current limit,
2A (typ), the MAX9768 enters a cycle-by-cycle current-
limit mode. In soft current-limit mode, the output is
clipped at 2A. When the output decreases so the out-
put current falls below 2A, normal operation resumes.
The effect of soft current limiting is a slight increase in
distortion. Most applications will not enter soft current-
limit mode unless the speaker or filter creates imped-
ance nulls below 8Ω.
Figure 2. MAX9768 Efficiency vs. Class AB Efficiency
SCLK
100
0
1
90
80
70
60
50
40
30
20
10
0
0
MAX9768
EFFICIENCY vs. OUTPUT POWER
2
CLASS AB
OUTPUT POWER (W)
4
Classic PWM (50% Duty Cycle)
6
Filterless Modulation
Soft Current Limit
PV
f
R
IN
FUNCTION
L
DD
8
= 1kHz
= 8Ω
= 12V
10