HFBR-5527 Agilent(Hewlett-Packard), HFBR-5527 Datasheet
HFBR-5527
Available stocks
Related parts for HFBR-5527
HFBR-5527 Summary of contents
Page 1
... With the recommended application circuit for 125 MBd operation, the performance of the complete data link is specified for 0-25 meters with plastic fiber. A wide variety of other digitizing circuits can be combined with the HFBR-5527 Series to optimize performance and cost at higher or lower data rates. 165 ...
Page 2
... HFBR-5527 125 MBd Data Link Data link operating conditions and performance are specified for the transmitter and receiver in Recommended Operating Conditions for the Circuits in Figures 1 and 2. Parameter Ambient Temperature Supply Voltage Data Input Voltage - Low Data Input Voltage - High Data Output Load ...
Page 3
Plastic Optical Fiber (1 mm POF) Transmitter Application Circuit: Performance of the transmitter in the recommended application circuit (Figure 1) for POF; 1-125 MBd Parameter Average Optical Power 1 mm POF Average Modulated Power 1 mm POF Optical ...
Page 4
Plastic and Hard Clad Silica Optical Fiber Receiver Application Circuit: [4] Performance of the receiver in the recommended application circuit (Figure 1); 1-125 MBd unless otherwise stated. Parameter Data Output Voltage - Low Data Output Voltage - High ...
Page 5
V ECL SERIAL DATA SOURCE 0.1 µ – µF 0.1 µF 10 µF 0.1 µ ECL SERIAL DATA RECEIVER 120 120 Figure 2. Recommended Power Supply Filter and +5 ...
Page 6
... Megabaud Fiber Optic Link Transmitter/Receiver Description The HFBR-5527 incorporates a 650 nm LED, a PIN photodiode, and transimpedance preamplifier. The 650 nm LED is suitable for use with current peaking to decrease optical response time and can be used with the PIN preamplifier to build an optical transceiver that can be operated at signaling rates from 1 to 125 ® ...
Page 7
... HFBR-5527 Transmitter Electrical/Optical Characteristics Parameter Symbol Transmitter Output Optical Power POF Transmitter Output Optical ® Power, 200 m HCS Output Optical Power Temperature Coefficient Peak Emission Wavelength Peak Wavelength Temperature Coefficient Spectral Width Forward Voltage Forward Voltage Temperature Coefficient Transmitter Numerical ...
Page 8
HP8082A PULSE BCP MODEL 300 GENERATOR 500 MHz BANDWIDTH SILICON AVALANCHE PHOTODIODE HP54002A 50 OHM 50 OHM BNC LOAD OSCILLOSCOPE INPUT POD RESISTOR Figure 5. Test Circuit for Measuring Unpeaked Rise and Fall Times. 2.4 0° C 2.2 25° C ...
Page 9
... It is recommended that pins 5 and 6 be connected to Rx ground to reduce coupling of electrical noise. Refer to Figure 1. The connections between pins 1 and 2 of the HFBR-5527 and pins 13 and 12 of the MC10H116 should be adjacent and nearly the same length to maximize the common mode rejection of the MC10H116 to eliminate cross talk between the transmitter and receiver ...
Page 10
... RECEIVER 9 10 2.3 Figure 9. Recommended Power Supply Filter Circuit. The HFBR-5527 is typically used to construct 125 MBd digital fiber-optic receivers which use the same +5 volt power supply that powers the host system’s microprocessors, CMOS logic, or TTL logic. To build a digital receiver, the analog HFBR-5527 ...
Page 11
BIAS & FILTER CIRCUITS Figure 10. Simplified Receiver Schematic. Figure 11. Typical Pulse Width Distortion vs. Peak Input Power. 4 POSITIVE SUPPLY 900 ANALOG OUTPUT 5.0 mA 2.3 GROUND Figure 12. Typical Output Spectral Noise Density vs. ...
Page 12
... HFBR-5527 Mechanical Dimensions 16 8.5 0.3 4.39 5.85 5.76 0.51 0.64 Printed Circuit Board Layout Dimensions 20.3 1. TOP VIEW ELECTRICAL PIN FUNCTIONS PIN NO OUT 2 RX GND 3 RX GND GND GND* 7 ANODE 8 CATHODE 9 CASE GND 10 CASE GND *NO INTERNAL CONNECTION 176 22 10.16 3.5 2.54 20 ALL DIMENSIONS IN MILLIMETERS (INCHES). ALL DIMENSIONS ± ...