EM-1RI Systemsensor, EM-1RI Datasheet

EM-1RI

Manufacturer Part Number

EM-1RI

Description

Relay Module

Manufacturer

Systemsensor

Datasheet

1.EM-1RI.pdf (2 pages)

Current page: 1 of 2
Download datasheet (256Kb)

www.DataSheet4U.com

INSTALLATION AND MAINTENANCE INSTRUCTIONS

EM-1RI Relay Module

SPECIFICATIONS

Normal Operating Voltage:

Standby Current:

Alarm Current:

Short Circuit Current, Dry Control Input:

Maximum Resistance, Dry Contact Input:

Temperature Range:

Humidity:

Dimensions:

Accessories:

NOTE: This module is not approved for use in the European Union, at or above 50VAC or 70VDC.

BEFORE INSTALLING

This information is included as a quick reference installation guide. Refer to the

appropriate control panel installation manual for detailed system information.

If the modules will be installed in an existing operational system, inform the

operator and local authority that the system will be temporarily out of service.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

Relay Module, Model EM-1RI, is to be designed for use in activation of the

types of products that are generally connected to an intelligent fire alarm sys-

tem. It provides two sets of form C contacts that switch together (one DPDT

relay). There is also an input that is capable of monitoring a dry set of contacts

for open or closed conditions. The module also has on-board short circuit iso-

lators to prevent shorts on the signaling line circuit from disabling more than

one device on the intelligent loop.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a listed compat-

ible control panel.

MOUNTING

The module mounts directly to 4-inch square electrical boxes. The box must

have a minimum depth of 2

row facing upward for proper operation of the IR programming tool. Surface

mounted electrical boxes (SMB500) are available from System Sensor.

D500-61-00

CURRENT RATING

1.5 A

.9 A

.5 A

.3 A

.7 A

3 A

2 A

1 A

2 A

LED INDICATOR

⁄

inches. Modules must be mounted with the ar-

15 to 30 VDC

580 µA max. average (continuous broadcasts)

2.0 mA (red LED on)

30 µA max. average (5VDC)

100 Ω

32°F to 120°F (0°C to 49°C)

10% to 93% RH Non-condensing

4.17˝ H × 4.26˝ W × 1.22˝ D; (106 mm H × 108 mm W × 31 mm D)

Wall cover plate (included); SMB500 Surface Mount Electrical Box; CB500 Control Module Barrier

MAXIMUM VOLTAGE

IR RECEIVER

70.7 VAC

110 VDC

125 VDC

125 VAC

30 VDC

25 VAC

C0166-00

WIRING

NOTE: All wiring must conform to applicable local codes, ordinances,

and regulations.

AUTO ADDRESSING

Eclipse Series devices are capable of supporting auto addressing, if the fire

alarm control panel is designed to do so. In auto addressing, the control panel,

through the use of each device’s on-board isolators, can automatically assign

device addresses.

In order to control which devices are addressed first in wiring configurations

with branches, a branch marker can be set at a particular device. A branch

marker is an electronic value from 0 to 255 stored in the device memory. The

branch markers are set with the IR configuration tool, EA-CT.

TERMINAL DEFINITIONS

All relay switch contacts are shipped in the standby state (open) state, but may

have transferred to the activated (closed) state during shipping. To ensure that

the switch contacts are in their correct state, modules must be made to com-

municate with the panel before connecting circuits controlled by the module.

Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

NOTE: Separate cable entry openings must be used to maintain required

spacing between power limited and non-power limited wiring. Optional

EA-CB may be required to separate power limited and non power limited

wiring in the electrical box.

Set the address on the module per job drawings using the IR configura-

tion tool (model no. EA-CT).

Secure module to electrical box (supplied by installer).

LOAD DESCRIPTION

Inductive (L/R=5ms)

Inductive (L/R=2ms)

Inductive (PF = .35)

Inductive (PF=.35)

(+) SLC in/out

(–) SLC in/out

(+) SLC in/out

(–) SLC in/out

(+) Dry Contact Input

(–) Dry Contact Input

Resistive

3825 Ohio Avenue, St. Charles, Illinois 60174

WARNING

T10

T11

T12

1.800.SENSOR2; Fax: 630.377.6495

Normally Closed #1

Common #1

Normally Open #1

Normally Closed #2

Common #2

Normally Open #2

APPLICATION

Non-Coded

www.systemsensor.com

Coded

I56-2023-005

Related parts for EM-1RI

EM-1RI Summary of contents

Page 1

... NOTICE: This manual should be left with the owner/user of this equipment. GENERAL DESCRIPTION Relay Module, Model EM-1RI designed for use in activation of the types of products that are generally connected to an intelligent fire alarm sys- tem. It provides two sets of form C contacts that switch together (one DPDT relay) ...

Page 2

... Company has the authority to increase or alter the obligations or limitations of this Warranty. The Company’s obligation of this Warranty shall be limited to the repair or replacement of any part of the module which is found to be defective in materials or workmanship under normal use and service during the three year period commencing with the date of manufacture. After phoning System Sensor’ ...

Related keywords

EM-1RI datasheet
EM-1RI data sheet
EM-1RI pdf datasheet
EM-1RI component
EM-1RI part
EM-1RI distributor
EM-1RI RoHS
EM-1RI datasheet download