120-1XXXXX-X Stancor, 120-1XXXXX-X Datasheet - Page 2

• Manufacturer Part Number: 120-1XXXXX-X
• Description: White-rodgers Dc Products
• Manufacturer: Stancor

• Not all part number combinations are available. Please contact your Sales Representative for available part numbers.
• Solenoids applied in battery charging circuits should be protected from higher than rated voltage during charging. The service life
• Circuits should be designed to provide safe operation should the solenoid fail in either the open or closed position.
• A back-up wrench must be used to hold the bottom nut stationary during installation.
Basic Part Number Series
02 – 6 Volt continuous
05 – 12 Volt continuous
06 – 12 Volt intermittent
07 – 14 Volt continuous
08 – 15 Volt continuous
14 – 24 Volt continuous
17 – 36 Volt continuous
19 – 36 Volt continuous
20 – 48 Volt continuous
may be affected by this condition and the solenoid may or may not operate the circuit as intended.
(special, 100 ohm coil)
1.375
W 3.000
Voltage/Duty
Coil
2.125
L
2.500
L
.281 WIDE X .400 LONG SLOT
Terminal Type 4 - Isolated Coil (STD Bracket)
.625
TYPE 120 PART NUMBERING SYSTEM
Terminal Type 4 - Isolated Coil (L Bracket)
1 – Isolated w/ #10-32
2 – Grounded w/ #10-32
3 – Isolated w/
4 – Grounded w/
6 – Grounded w/ #8-32
7 – Isolated w/ #10-32
8 – Grounded w/ #10-32
2.125
.625
1
terminal
terminal
1
tapered terminal
terminal
terminal
/
(15 in-lb torque spec.)
/
Coil Termination
4
4
” Q.C. terminal
.281 WIDE X .400 LONG SLOT
1 2 0 – 1 x x x x x - x
” Q.C. terminal
W 2.875
1.375
SPNO
(0.220 min. length)
(0.220 min. length)
(0.451 min. length)
(0.451 min. length)
2.125
#10-32 UNF-2A
THREAD TYP.
APPLICATION NOTES
CIRCUIT DIAGRAM
H MAX.
3.253
H MAX.
3.250
Termination
1 – AgCdO w/
3 – Cu w/
4 – Cu w/
5 – AgCdO w/
.900
terminal
terminal
terminal
Contact Material and
1 – Standard bracket
2 – “L” shaped bracket
5
1
/
/
16
4
(0.388 min. length)
(0.388 min. length)
(0.495 min. length)
”-20 terminal
(55 in-lb torque spec.)
”-24
5
5
Mounting
/
/
Bracket
16
16
See Part Numbering
System chart, above
.875
”-24
”-24
THD (2 PLACES)
5
/
16
”-24 UNF-2A
5
/
THREAD TYP.
16
”-24 UNF-2A
.875
No dash – Standard assem-
1 – Without hardware
2 – Extra hardware loosely
4 – Customer requested
5 – Mounting bracket zinc-
6 – Customer requested
7 – Customer requested
8 – No hardware, mounting
9 – Customer requested
11 – Customer requested
Factory Assigned Specials
(where undefined, contact factory)
#10-32 UNF-2A
THD (PLACES)
bly, hardware sent bulk
mounted to solenoid
markings
plated and dichromate dip
markings
markings
bracket as -5 option
markings
markings
System chart, above
See Part Numbering
CIRCUIT DIAGRAM
R-4002B
0746