HA1-5320883 Intersil Corporation, HA1-5320883 Datasheet

HA1-5320883

Manufacturer Part Number

HA1-5320883

Description

High Speed Precision Sample and Hold Amplifier

Manufacturer

Intersil Corporation

Datasheet

1.HA1-5320883.pdf (12 pages)

Current page: 1 of 12
Download datasheet (91Kb)

July 1994

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

http://www.intersil.com or 407-727-9207

Features

• This Circuit is Processed in Accordance to MIL-STD-

• Gain, DC . . . . . . . . . . . . . . . . . . . . . . . . 2 x 10

• Acquisition Time . . . . . . . . . . . . . . . 1.0 s (0.01%) (Typ)

• Droop Rate . . . . . . . . . . . . . . . . 0.08 V/ s (+25

• Aperture Time. . . . . . . . . . . . . . . . . . . . . . . . . 25ns (Typ)

• Hold Step Error . . . . . . . . . . . . . . . . . . . . . . 1.0mV (Typ)

• Internal Hold Capacitor

• Fully Differential Input

• TTL Compatible

Applications

• High Bandwidth Precision Data Acquisition Systems

• Inertial Navigation and Guidance Systems

• Ultrasonics

• SONAR / RADAR

• Digital to Analog Converter Deglitcher

Pinouts

OFFSET ADJ

883 and is Fully Conformant Under the Provisions of

Paragraph 1.2.1.

OFFSET ADJ

SIG GND

OUTPUT

+INPUT

-INPUT

V-

HA-5320/883 (CERDIP)

HA-5320/883 (CLCC)

9 10 11 12 13

TOP VIEW

1 20 19

17 V/ s (Full Temperature) (Typ)

S/H CONTROL

SUPPLY GND

V+

INT. BW

EXT

Intersil Corporation 1999

High Speed Precision Sample and Hold Ampliﬁer

V/V (Typ)

C) (Typ)

Ordering Information

Functional Diagram

HA1-5320/883

HA4-5320/883

PART NUMBER

CONTROL

7-3

+INPUT

-INPUT

Description

The HA-5320/883 was designed for use in precision, high speed

data acquisition systems.

The circuit consists of an input transconductance ampliﬁer

capable of providing large amounts of charging current, a low

leakage analog switch, and an output integrating ampliﬁer. The

analog switch sees virtual ground as its load; therefore, charge

injection on the hold capacitor is constant over the entire input/

output voltage range. The pedestal voltage resulting from this

charge injection can be adjusted to zero by use of the offset

adjust inputs. The device includes a hold capacitor. However, if

improved droop rate is required at the expense of acquisition

time, additional hold capacitance may be added externally.

This monolithic device is manufactured using the Intersil

Dielectric Isolation Process, minimizing stray capacitance and

eliminating SCR’s. This allows higher speed and latch-free

operation. For further information, please see Application Note

AN538.

S/H

HA5320/883

TEMPERATURE

-55

SUPPLY

OFFSET

ADJUST

GND

C to +125

RANGE

HA-5320/883

V-

EXT

GND

SIG

V+

Spec Number

14 Lead CerDIP

20 Lead Ceramic LCC

INTEGRATOR

BANDWIDTH

100pF

File Number

PACKAGE

511096-883

OUTPUT

2927.3

Related parts for HA1-5320883

HA1-5320883 Summary of contents

Page 1

... This monolithic device is manufactured using the Intersil Dielectric Isolation Process, minimizing stray capacitance and eliminating SCR’s. This allows higher speed and latch-free operation. For further information, please see Application Note AN538. Ordering Information PART NUMBER HA1-5320/883 HA4-5320/883 EXT Functional Diagram -INPUT 1 2 ...

Page 2

Absolute Maximum Ratings Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . ...

Page 3

TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at +15V -15V; V Unless Otherwise Speciﬁed PARAMETERS SYMBOL Output Voltage Swing + Power Supply Current + Power Supply Rejection +PSRR Ratio ...

Page 4

TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER SYMBOL Hold Mode Feedthrough V V HMF Hold Step Error V V ERROR T Sample Mode Noise 10MHz, V N(SAMPLE) Voltage R Hold Mode Noise 10MHz, V N(HOLD) ...

Page 5

Die Characteristics DIE DIMENSIONS 152 x 19 1mils METALLIZATION: Type: Al Å Å Thickness: 16k 2k GLASSIVATION: Type: Nitride ( over Silox (SiO 3 4 Å Å Silox Thickness: 12k 2k Å Å Nitride ...

Page 6

Burn-In Circuits - NOTES 100k , 5%, (per socket 0.01 F minimum per socket or 0.1 F minimum per row ...

Page 7

Packaging -D- -A- E -B- bbb BASE Q PLANE A -C- SEATING PLANE aaa ccc NOTES: 1. ...

Page 8

Packaging (Continued HA-5320/883 J20.A MIL-STD-1835 CQCC1-N20 (C-2) 20 PAD METAL SEAL LEADLESS CERAMIC CHIP CARRIER SYMBOL A 0.060 A1 ...

Page 9

Semiconductor DESIGN INFORMATION August 1999 The information contained in this section has been developed through characterization by Intersil Semiconductor and is for use as applica- tion and design information only. No guarantee is implied. Applying the HA-5320 The HA-5320 has ...

Page 10

DESIGN INFORMATION The information contained in this section has been developed through characterization by Intersil Semiconductor and is for use as applica- tion and design information only. No guarantee is implied. Test Circuits S/H CONTROL INPUT CHARGE TRANSFER TEST 1. ...

Page 11

DESIGN INFORMATION The information contained in this section has been developed through characterization by Intersil Semiconductor and is for use as applica- tion and design information only. No guarantee is implied. Performance Curves V SUPPLY TYPICAL SAMPLE AND HOLD PERFORMANCE ...

Page 12

... All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certiﬁcation. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or speciﬁcations at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use ...

Related keywords

HA1-5320883 datasheet
HA1-5320883 data sheet
HA1-5320883 pdf datasheet
HA1-5320883 component
HA1-5320883 part
HA1-5320883 distributor
HA1-5320883 RoHS
HA1-5320883 datasheet download