MC13155 Motorola, MC13155 Datasheet - Page 11

• Manufacturer Part Number: MC13155
• Description: WIDEBAND FM IF
• Manufacturer: Motorola

Quadrature Detector
2.0 pF capacitors between Pins 7 and 8 and Pins 9 and 10.
For wideband data applications, such as FM video and
satellite receivers, the drive to the detector can be increased
with additional external capacitors between these pins, thus,
the recovered video signal level output is increased for a
given bandwidth (see Figure 11A and Figure 11B).
the loaded Q of the LC tank circuit. The following equation
defines the components which set the detector circuit’s
bandwidth:
where: R T is the equivalent shunt resistance across the LC
Tank and X L is the reactance of the quadrature inductor at the
IF frequency (X L = 2 fL).
LC Tank with the PCB and parasitic device capacitance at the
desired IF center frequency as predicted by:
where: L is the parallel tank inductor and C p is the equivalent
parallel capacitance of the parallel resonant tank circuit.
at 70 MHz and a loaded Q of 5. The loaded Q of the
quadrature detector is chosen somewhat less than the Q of
the IF bandpass. For an IF frequency of 70 MHz and an
IF bandpass of 10.9 MHz, the IF bandpass Q is
approximately 6.4.
Example:
should be greater than 15 pF making it greater than the
internal device and PCB parasitic capacitance, Cint
3.0 pF).
Rewrite Equation 2 and solve for L:
MOTOROLA ANALOG IC DEVICE DATA
The quadrature detector is coupled to the IF with internal
The wideband performance of the detector is controlled by
The inductor and capacitor are chosen to form a resonant
The following is a design example for a wideband detector
Let the external Cext = 20 pF. (The minimum value here
L = (0.159) 2 /(C p fc 2 )
L = 198 nH, thus, a standard value is chosen.
L = 0.22 H (tunable shielded inductor).
C p = Cint + Cext = 23 pF
fc = (2
Q = R T /X L
(LC p )) –1
MC13155
(1)
(2)
required loaded Q of 5 can be calculated by rearranging
Equation 1:
Pins 8 and 9 is approximately 3200
determining the external resistance, Rext which is calculated
from:
SAW Filter
bandwidth may be several MHz wide. A good rule of thumb is
to choose the IF frequency about 10 or more times greater
than the IF occupied bandwidth. The IF bandpass filter is a
SAW filter in video data applications where a very selective
response is needed (i.e., very sharp bandpass response).
The evaluation PCB is laid out to accommodate two SAW
filter package types: 1) A five–leaded plastic SIP package.
Recommended part numbers are Siemens X6950M which
operates at 70 MHz; 10.4 MHz 3 dB passband, X6951M
(X252.8) which operates at 70 MHz; 9.2 MHz 3 dB passband;
and X6958M which operates at 70 MHz, 6.3 MHz 3 dB
passband, and 2) A four–leaded TO–39 metal can package.
Typical insertion loss in a wide bandpass SAW filter is 25 dB.
impedances of 50
board layout, space is provided to add a matching network,
such as a 1:4 surface mount transformer between the SAW
filter output and the input to the MC13155. A 1:4 transformer,
made by Coilcraft and Mini Circuits, provides a suitable
interface (see Figures 16, 17 and 18). In the circuit and
layout, the SAW filter and the MC13155 are differentially
configured with interconnect traces which are equal in length
and symmetrical. This balanced feed enhances RF stability,
phase linearity, and noise performance.
The value of the total damping resistor to obtain the
The internal resistance, Rint between the quadrature tank
In wideband video data applications, the IF occupied
The above SAW filters require source and load
Rext = ((R T )(Rint))/ (Rint – R T )
Rext = 570, thus, choose the standard value.
Rext = 560 .
R T = Q(2 fL)
R T = 5 (2 )(70)(0.22) = 483.8 .
to assure stable operation. On the PC
and is considered in
11