MP1482 MPS, MP1482 Datasheet - Page 7

• Manufacturer Part Number: MP1482
• Description: 2a, 18v Synchronous Rectified Step-down Converter
• Manufacturer: MPS

APPLICATIONS INFORMATION
COMPONENT SELECTION
Setting the Output Voltage
The output voltage is set using a resistive
voltage divider from the output voltage to FB pin.
The voltage divider divides the output voltage
down to the feedback voltage by the ratio:
Where V
the output voltage.
Thus the output voltage is:
R2 can be as high as 100kΩ, but a typical value
is 10kΩ. Using the typical value for R2, R1 is
determined by:
For example, for a 3.3V output voltage, R2 is
10kΩ, and R1 is 26.1kΩ.
Inductor
The inductor is required to supply constant
current to the output load while being driven by
the switched input voltage. A larger value
inductor will result in less ripple current that will
result in lower output ripple voltage. However,
the larger value inductor will have a larger
physical size, higher series resistance, and/or
lower saturation current. A good rule for
determining the inductance to use is to allow
the peak-to-peak ripple current in the inductor
to be approximately 30% of the maximum
switch current limit. Also, make sure that the
peak inductor current is below the maximum
switch current limit. The inductance value can
be calculated by:
Where V
input voltage, f
ΔI
MP1482 Rev. 1.2
1/13/2010
L
is the peak-to-peak inductor ripple current.
FB
R
OUT
1
is the feedback voltage and V
=
L
10
is the output voltage, V
V
=
S
OUT
V
.
83
f
FB
is the switching frequency, and
S
V
×
=
OUT
×
=
. 0
Δ
(
V
V
I
923
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
L
OUT
OUT
MP1482 – 2A, 18V SYNCHRONOUS RECTIFIED, STEP-DOWN CONVERTER
×
⎛
⎜ ⎜
⎝
×
R
1
−
1
R
−
R
. 0
+
1
2
R
V
923
R
+
V
2
OUT
2
R
IN
2
)
⎞
⎟ ⎟
⎠
(kΩ)
© 2010 MPS. All Rights Reserved.
IN
is the
www.MonolithicPower.com
OUT
is
Choose an inductor that will not saturate under
the maximum inductor peak current. The peak
inductor current can be calculated by:
Where I
The choice of which style inductor to use mainly
depends on the price vs. size requirements and
any EMI requirements.
Optional Schottky Diode
During the transition between high-side switch
and low-side switch, the body diode of the low-
side power MOSFET conducts the inductor
current. The forward voltage of this body diode
is high. An optional Schottky diode may be
paralleled between the SW pin and GND pin to
improve overall efficiency. Table 1 lists example
Schottky diodes and their Manufacturers.
Input Capacitor
The input current to the step-down converter is
discontinuous, therefore a capacitor is required
to supply the AC current to the step-down
converter while maintaining the DC input
voltage. Use low ESR capacitors for the best
performance. Ceramic capacitors are preferred,
but tantalum or low-ESR electrolytic capacitors
may also suffice.
dielectrics when using ceramic capacitors.
Since the input capacitor (C1) absorbs the input
switching current it requires an adequate ripple
current rating. The RMS current in the input
capacitor can be estimated by:
Part Number
MBRS130
SK13
B130
Table 1—Diode Selection Guide
LOAD
I
LP
I
C
=
1
is the load current.
I
=
LOAD
I
LOAD
Voltage/Current
+
2
×
30V, 1A
30V, 1A
30V, 1A
×
V
Rating
Choose X5R or X7R
OUT
f
V
S
V
OUT
×
IN
L
×
×
⎛
⎜
⎜
⎝
⎛
⎜ ⎜
⎝
1
1
−
−
V
V
OUT
V
V
IN
OUT
International
IN
Diodes, Inc.
Diodes, Inc.
⎞
⎟
⎟
⎠
Rectifier
Vendor
⎞
⎟ ⎟
⎠
7