IDT72V90823 Integrated Device Technology, IDT72V90823 Datasheet - Page 13
![no-image](/images/no-image-200.jpg)
IDT72V90823
Manufacturer Part Number
IDT72V90823
Description
3.3 Volt Time Slot Interchange Digital Switch
Manufacturer
Integrated Device Technology
Datasheet
1.IDT72V90823.pdf
(27 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT72V90823BC
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Part Number:
IDT72V90823BC
Manufacturer:
IDT
Quantity:
20 000
Company:
Part Number:
IDT72V90823BCG
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT72V90823J
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT72V90823J8
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT72V90823JG
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Company:
Part Number:
IDT72V90823PQF
Manufacturer:
IDT
Quantity:
6
Company:
Part Number:
IDT72V90823PQF
Manufacturer:
IDT
Quantity:
917
Part Number:
IDT72V90823PQF
Manufacturer:
IDT
Quantity:
20 000
TABLE 10 — FRAME ALIGNMENT REGISTER (FAR) BITS
IDT72V90823 3.3V TIME SLOT INTERCHANGE
DIGITAL SWITCH 2,048 x 2,048
15-13
10-0
Bit
12
11
Read/Write Address:
Reset Value:
15
0
Unused
CFE
(Complete Frame Evaluation)
FD11
(Frame Delay Bit 11)
FD10-0
(Frame Delay Bits)
ST-BUS
14
0
Offset Value
Offset Value
GCI Frame
FE Input
FE Input
13
Name
Frame
0
CLK
CLK
CFE
02
0000
12
H
,
H
.
FD11 FD10
11
0
0
Must be zero for normal operation.
When CFE = 1, the frame evaluation is completed and bits FD10 to FD0 bits contains a valid frame alignment
offset. This bit is reset to zero, when SFE bit in the IMS register is changed from 1 to 0.
The falling edge of FE (or rising edge for GCI mode) is sampled during the CLK-high phase (FD11 = 1)
or during the CLK-low phase (FD11 = 0). This bit allows the measurement resolution to ½ CLK cycle.
The binary value expressed in these bits refers to the measured input offset value. These bits are rest to
zero when the SFE bit of the IMS register changes from 1 to 0. (FD10 – MSB, FD0 – LSB)
Figure 4. Example for Frame Alignment Measurement
10
1
1
2
2
FD9
9
3
3
FD8
4
4
8
5
5
FD7
(FD[10:0] = 06
(FD11 = 0, sample at CLK LOW phase)
7
13
6
6
FD6
7
7
6
8
8
H
)
(FD[10:0] = 09
(FD11 = 1, sample at CLK HIGH phase)
Description
FD5
5
9
9
10
10
FD4
4
H
11
11
)
FD3
3
12
COMMERCIAL TEMPERATURE RANGE
12
13
13
FD2
2
14
14
5712 drw07
FD1
15
1
15
16
FD0
0