MCP1316 Microchip Technology, MCP1316 Datasheet - Page 2

• Manufacturer Part Number: MCP1316
• Description: Voltage Supervisor
• Manufacturer: Microchip Technology

MCP131X/2X
1.0
Absolute Maximum Ratings†
Supply Voltage (V
Input current (V
Output current (RST) . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
Voltage on all inputs and outputs, except Open-Drain RST
(with no internal pull-up resistor), w.r.t. V
Voltage on Open-Drain RST
(with no internal pull-up resistor) w.r.t. V
Storage temperature . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient temp. with power applied . . . . . . . .-40°C to +125°C
Maximum Junction temp. with power applied . . . . . . . . 150°C
Power Dissipation (T
ESD protection on all pins
DC CHARACTERISTICS
DS21985A-page 2
Electrical Specifications: Unless otherwise indicated, all limits are specified for V
(only MCP1320, MCP1321 and MCP1322), T
Operating Voltage Range
Specified V
Operating Current:
Note 1:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to (V
5-Pin SOT-23A .......................................................240 mW
2:
3:
4:
5:
6:
ELECTRICAL
CHARACTERISTICS
Trip point is ±1.5% from typical value.
Trip point is ±2.5% from typical value.
Hysterysis is minimum = 1%, max = 6% at +25°C.
This specification allows this device to be used in PICmicro
In-Circuit Serial Programming™ (ICSP™) feature (see device-specific programming specifications for
voltage requirements). The total time that the RST pin can be above the maximum device operational volt-
age (5.5V) is 100s. Current into the RST pin should be limited to 2 mA. It is recommended that the device
operational temperature be maintained between 0°C to +70°C (+25°C preferred). For additional informa-
tion, refer to Figure 2-35.
This parameter is established by characterization and is not 100% tested.
Custom ordered voltage trip point; minimum order volume requirement. Information available upon request.
DD
Parameters
DD
Value to V
DD
) . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
A
to V
70°C):
SS
) . . . . . . . . . . . . . . . . . . . . . . 7.0V
OUT
Low
SS
SS
. . -0.6V to 13.5V
Sym
V
V
I
DD
DD
DD
DD
A
+ 1.0V)
= -40°C to +125°C.
4 kV
Min
1.0
1.0
—
—
—
—
Typ
—
—
5
1
1
5
† Notice: Stresses above those listed under “Maximum Rat-
ings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied. Expo-
sure to maximum rating conditions for extended periods may
affect device reliability.
Max
5.5
10
10
®
—
2
2
microcontroller applications that require the
Units
μA
μA
μA
μA
V
V
DD
I
Watchdog Timer Active
Watchdog Timer Inactive
V
Reset Delay Timer Active
= 1V to 5.5V, R
RST
© 2005 Microchip Technology Inc.
DD
< V
= 10 μA, V
TRIP
Conditions
PU
RST
= 100 k
< 0.3V