TDA4687 Philips Semiconductors, TDA4687 Datasheet
TDA4687
Available stocks
Related parts for TDA4687
TDA4687 Summary of contents
Page 1
... DATA SHEET TDA4687 Video processor with automatic cut-off control Product specification Supersedes data of May 1993 File under Integrated Circuits, IC02 INTEGRATED CIRCUITS 1997 Jun 23 ...
Page 2
... The TDA4686 is like TDA4687 but intended for double line frequency application. PACKAGE DESCRIPTION plastic dual in-line package; 28 leads (600 mil) 2 Product specifi ...
Page 3
... BK 2-level sandcastle pulse RGB input signals at pins 10, 11 and 12 i(p-p) (peak-to-peak value) V RGB outputs at pins 24, 22 and 20 (black-to-white value) o(b-w) T operating ambient temperature amb 1997 Jun 23 PARAMETER 3 Product specification TDA4687 MIN. TYP. MAX. UNIT 7.2 8.0 8 0.45 V 1.33 V 1. ...
Page 4
... Philips Semiconductors Video processor with automatic cut-off control BLOCK DIAGRAM 1997 Jun 23 4 Product specification TDA4687 pagewidth full handbook, ...
Page 5
... FSW 1 SC Fig.2 Pin configuration. 5 Product specification TDA4687 1 28 SCL 2 27 SDA 3 26 HUE TDA4687 VFB PDL 14 15 BCL MED721 ...
Page 6
... C-bus is a bidirectional, two-wire, serial data bus for intercommunication between ICs in an equipment. The microcontroller transmits data to the I in the TDA4687 over the serial data line SDA (pin 27) synchronized by the serial clock line SCL (pin 28). Both lines are normally connected to a positive voltage supply through pull-up resistors ...
Page 7
... Jun 23 MSB module address Fig.3 The module address byte. STA MAD SAD START condition condition data byte MAD SAD data byte data bytes 7 Product specification LSB 0 0 ACK R/W MED710 STO MED697 STOP STO MED698 STOP condition TDA4687 ...
Page 8
... Reserved subaddresses 07H, 08H, 09H, 0BH and 0FH are treated as legal but have no effect. Subaddresses outside the range 00H and 0FH are not acknowledged by the device. Subaddresses are stored in the TDA4687 to address the following parameters and functions (see Table 1): Brightness adjust Saturation adjust ...
Page 9
... AA5 AA4 SC5 X BREN BCOF X X MOD2 Product specification TDA4687 A03 A02 A01 A13 A12 A11 A23 A22 A21 A33 A32 A31 A43 A42 A41 A53 A52 A51 A63 A62 A61 ...
Page 10
... PARAMETER 10 Product specification TDA4687 INPUT SELECTED RGB RGB MIN. MAX. 8 0.1 +8 +0.6 20 ...
Page 11
... Product specification TDA4687 = 8 nominal signal P amb MIN. TYP. MAX. 7.2 8.0 8.8 60 1.33 1.05 4.1 ...
Page 12
... Product specification MIN. TYP. inputs (control bits: see Table 2) 0.9 4 inputs (control bits: see Table 0.9 4.0 2 C-bus control; subaddress 01H (bit resolution TDA4687 MAX. UNIT 0 0 ...
Page 13
... Jun 23 CONDITIONS output clamping; BCOF = MHz MHz path MHz 1 path MHz Product specification TDA4687 MIN. TYP. MAX. UNIT 2 0.8 V 6.8 V 2.3 2.5 2 ...
Page 14
... Jun 23 CONDITIONS for LOW for HIGH pin 18 open-circuit; note 7 at 00H at 3FH during peak white switch-on delay 1 switch-on delay 1; note 11 switch-on delay 1 during leakage measurement period (cut-off MEAS ref 14 Product specification TDA4687 MIN. TYP. MAX. 2.5 4.5 5.0 5 4.0 2.0 2.5 1.6 ) acts on RGB outputs under I pdl 3.0 7 4.5 4.0 2 ...
Page 15
... SU;DAT 1997 Jun 23 CONDITIONS MIN. during cut-off measurement lines outside measurement time during leakage measurement period outside measurement time at 3FH 4.8 at 20H at 00H 500 0 3.0 4.7 4.0 3.0 3.0 0.25 15 Product specification TDA4687 TYP. MAX. UNIT 0.3 mA 0.1 A 0.4 mA 0 3 100 kHz 1 ...
Page 16
... The hue control output at pin emitter follower with current source. 1997 Jun 23 Y) colour difference input signals are for a 75% colour-bar signal. 2 C-bus under subaddress 0AH. When an RGB output exceeds 16 Product specification TDA4687 . The threshold voltages pin 18 is always LOW neither P ...
Page 17
... V are the NTSC modified colour difference signals; this is equivalent Fig.6 Cut-off measurement pulse. 17 NTSC 0 115 1.97 2.03 NMEN 0 1 0.19V 0.27V 0.22V MHA697 (1) (2) ultra-black Product specification TDA4687 PAL 0 90 1.14 2. ...
Page 18
... Timing controlled by additional vertical flyback pulse (VFB leakage current measurement time. MR, MG cut-off measurement pulses. Fig.7 Leakage and cut-off current measurement timing diagrams. 1997 Jun 23 a. Timing controlled by sandcastle pulse Product specification TDA4687 MHA698 MHA699 ...
Page 19
... Philips Semiconductors Video processor with automatic cut-off control INTERNAL PIN CONFIGURATION 1997 Jun 23 19 Product specification TDA4687 pagewidth full handbook, ...
Page 20
... Philips Semiconductors Video processor with automatic cut-off control TEST AND APPLICATION INFORMATION 1997 Jun 23 20 Product specification TDA4687 ...
Page 21
... 1.7 0.53 0.32 36.0 14.1 1.3 0.38 0.23 35.0 13.7 0.013 0.066 0.020 1.41 0.56 0.009 0.051 0.014 1.34 0.54 REFERENCES JEDEC EIAJ MO-015AH 3.9 15.80 17.15 2.54 15.24 3.4 15.24 15.90 0.15 0.62 0.10 0.60 0.13 0.60 EUROPEAN PROJECTION Product specification TDA4687 SOT117 ( max. 0.25 1.7 0.68 0.01 0.067 0.63 ISSUE DATE 92-11-17 95-01-14 ...
Page 22
... If the bit temperature is between 300 and 400 C, contact may seconds components conveys a license under the Philips’ system provided the system conforms to the I 22 Product specification TDA4687 ). If the stg max 2 C patent to use the 2 C specification defined by ...
Page 23
... Philips Semiconductors Video processor with automatic cut-off control 1997 Jun 23 NOTES 23 Product specification TDA4687 ...
Page 24
... Tel. +46 8 632 2000, Fax. +46 8 632 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. +41 1 488 2686, Fax. +41 1 481 7730 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel ...