DS2780 Maxim Integrated Products, DS2780 Datasheet - Page 20

no-image

DS2780

Manufacturer Part Number
DS2780
Description
Stand-Alone Fuel Gauge IC
Manufacturer
Maxim Integrated Products
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS2780
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
DS2780E
Manufacturer:
MAIXM
Quantity:
20 000
Part Number:
DS2780E+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
DS2780E+TR
Manufacturer:
TI-CC
Quantity:
5 728
Part Number:
DS2780G+
Manufacturer:
MAXIM/美信
Quantity:
20 000
www.DataSheet4U.com
Table 3. PARAMETER EEPROM MEMORY BLOCK 1
1-WIRE BUS SYSTEM
The 1-Wire bus is a system that has a single bus master and one or more slaves. A multidrop bus is a 1-Wire bus
with multiple slaves. A single-drop bus has only one slave device. In all instances, the DS2780 is a slave device.
The bus master is typically a microprocessor in the host system. The discussion of this bus system consists of four
topics: 64-bit net address, hardware configuration, transaction sequence, and 1-Wire signaling.
64-BIT NET ADDRESS
Each DS2780 has a unique, factory-programmed 1-Wire net address that is 64 bits in length. The first eight bits are
the 1-Wire family code (32h for DS2780). The next 48 bits are a unique serial number. The last eight bits are a
cyclic redundancy check (CRC) of the first 56 bits (see Figure 17). The 64-bit net address and the 1-Wire I/O
circuitry built into the device enable the DS2780 to communicate through the 1-Wire protocol detailed in the 1-Wire
Bus System section of this data sheet.
Figure 17. 1-Wire Net Address Format
CRC GENERATION
The DS2780 has an 8-bit CRC stored in the most significant byte of its 1-Wire net address. To ensure error-free
transmission of the address, the host system can compute a CRC value from the first 56 bits of the address and
compare it to the CRC from the DS2780. The host system is responsible for verifying the CRC value and taking
action as a result. The DS2780 does not compare CRC values and does not prevent a command sequence from
proceeding as a result of a CRC mismatch. Proper use of the CRC can result in a communication channel with a
very high level of integrity.
The CRC can be generated by the host using a circuit consisting of a shift register and XOR gates as shown in
Figure 17, or it can be generated in software. Additional information about the Dallas 1-Wire CRC is available in
ADDRESS
(HEX)
6A
6B
6C
6D
6E
60
61
62
63
64
65
66
67
68
69
6F
CONTROL - Control Register
AB - Accumulation Bias
AC - Aging Capacity MSB
AC - Aging Capacity LSB
VCHG - Charge Voltage
IMIN - Minimum Charge Current
VAE - Active Empty Voltage
IAE - Active Empty Current
Active Empty 40
RSNSP - Sense Resistor Prime
Full 40 MSB
Full 40 LSB
Full 3040 Slope
Full 2030 Slope
Full 1020 Slope
Full 0010 Slope
8-BIT CRC
MSb
DESCRIPTION
48-BIT SERIAL NUMBER
20 of 27
ADDRESS
(HEX)
7A
7B
7C
7D
7E
70
71
72
73
74
75
76
77
78
79
7F
AE 3040 Slope
AE 2030 Slope
AE 1020 Slope
AE 0010 Slope
SE 3040 Slope
SE 2030 Slope
SE 1020 Slope
SE 0010 Slope
RSGAIN - Sense Resistor Gain MSB
RSGAIN - Sense Resistor Gain LSB
RSTC - Sense Resistor Temp. Coeff.
FRSGAIN - Factory Gain MSB
FRSGAIN - Factory Gain LSB
Reserved
Reserved
Reserved
8-BIT FAMILY
CODE (32h)
DS2780 Stand-Alone Fuel Gauge IC
DESCRIPTION
LSb

Related parts for DS2780