MCP4531 Microchip Technology Inc., MCP4531 Datasheet - Page 42

• Manufacturer Part Number: MCP4531
• Description: 7/8-bit Single/dual I 2 C Digital Pot With Non-volatile Memory
• Manufacturer: Microchip Technology Inc.

MCP454X/456X/464X/466X
REGISTER 4-2:
DS22107A-page 42
bit 8
Legend:
R = Readable bit
-n = Value at POR
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
GCEN
R/W-1
These bits do not affect the wiper register values.
GCEN: General Call Enable bit
This bit specifies if I
1 = Enable Device to “Accept” the General Call Address (0000h)
0 = The General Call Address is disabled
R1HW: Resistor 1 Hardware Configuration Control bit
This bit forces Resistor 1 into the “shutdown” configuration of the Hardware pin
1 = Resistor 1 is NOT forced to the hardware pin “shutdown” configuration
0 = Resistor 1 is forced to the hardware pin “shutdown” configuration
R1A: Resistor 1 Terminal A (P1A pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Terminal A to the Resistor 1 Network
1 = P1A pin is connected to the Resistor 1 Network
0 = P1A pin is disconnected from the Resistor 1 Network
R1W: Resistor 1 Wiper (P1W pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Wiper to the Resistor 1 Network
1 = P1W pin is connected to the Resistor 1 Network
0 = P1W pin is disconnected from the Resistor 1 Network
R1B: Resistor 1 Terminal B (P1B pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Terminal B to the Resistor 1 Network
1 = P1B pin is connected to the Resistor 1 Network
0 = P1B pin is disconnected from the Resistor 1 Network
R0HW: Resistor 0 Hardware Configuration Control bit
This bit forces Resistor 0 into the “shutdown” configuration of the Hardware pin
1 = Resistor 0 is NOT forced to the hardware pin “shutdown” configuration
0 = Resistor 0 is forced to the hardware pin “shutdown” configuration
R0A: Resistor 0 Terminal A (P0A pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Terminal A to the Resistor 0 Network
1 = P0A pin is connected to the Resistor 0 Network
0 = P0A pin is disconnected from the Resistor 0 Network
R0W: Resistor 0 Wiper (P0W pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Wiper to the Resistor 0 Network
1 = P0W pin is connected to the Resistor 0 Network
0 = P0W pin is disconnected from the Resistor 0 Network
R0B: Resistor 0 Terminal B (P0B pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Terminal B to the Resistor 0 Network
1 = P0B pin is connected to the Resistor 0 Network
0 = P0B pin is disconnected from the Resistor 0 Network
R1HW
R/W-1
TCON BITS (ADDRESS = 0x04)
W = Writable bit
‘1’ = Bit is set
R/W-1
R1A
2
C General Call commands are accepted
R/W-1
R1W
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-1
R1B
(1)
R0HW
R/W-1
x = Bit is unknown
R/W-1
R0A
© 2008 Microchip Technology Inc.
R/W-1
R0W
R/W-1
R0B
bit 0