MIC2025 Micrel Semiconductor, MIC2025 Datasheet
![no-image](/images/manufacturer_photos/0/4/435/micrel_semiconductor_sml.jpg)
MIC2025
Available stocks
Related parts for MIC2025
MIC2025 Summary of contents
Page 1
... Both devices employ soft-start circuitry that minimizes inrush current in applications where highly capacitive loads are employed. A fault status output flag is provided that is asserted during overcurrent and thermal shutdown condi- tions. The MIC2025/75 is available in the MM8™ 8-lead MSOP and 8-lead SOP. Typical Application Logic Controller VIN OVERCURRENT 1µ ...
Page 2
... EN 2 FLG 3 GND OUT 7 IN MIC2025/2075 Enable Temperature Range Active High – +85 C Active Low – +85 C Active High – +85 C Active Low – +85 C Active High – +85 C Active Low – +85 C Active High – ...
Page 3
... 5. 5V 500mA IN OUT V = 3.3V 500mA IN OUT MIC2025/2075 (output off) MIC2075 (during thermal shutdown state see “Timing Diagrams” see “Timing Diagrams” see “Timing Diagrams” ...
Page 4
... The device is not guaranteed to function outside its operating rating. Note 3. Devices are ESD sensitive. Handling precautions recommended. Note 4. See “Functional Characteristics: Current-Limit Response” graph. Test Circuit Timing Diagrams V OUT OUT OUT MIC2025/2075 Condition I = 10mA 10mA 3. FLAG T increasing ...
Page 5
... Turn-On Rise Time vs. Input Voltage 5.0 4.0 +85 C 3.0 +25 C -40 C 2.0 1 2.5 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) Enable Threshold vs. Temperature 2.5 2.0 V RISING EN 1.5 V FALLING EN 1.0 0 -40 - 100 TEMPERATURE ( C) Enable Threshold vs. Input Voltage 2.5 2.0 V RISING EN 1.5 V FALLING EN 1.0 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) MIC2025/2075 ...
Page 6
... MIC2025/2075 Flag Delay vs. Temperature 3. -40 - 100 TEMPERATURE ( C) MIC2025/2075 Flag Delay vs. Input Voltage 2.5 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) 6 Micrel UVLO Threshold vs. Temperature 3.0 V RISING IN 2.5 2.0 V FALLING IN 1.5 1.0 0.5 0 -40 - 100 ...
Page 7
... UVLO—V Falling IN (MIC2025-1) 2. TIME (25ms/div.) Turnoff Response (MIC2025- 147 144mA L TIME (2.5ms/div.) Enable Into Short (MIC2025-1) 3.1ms ( 640mA Short-Circuit Current TIME (1ms/div.) MIC2025/2075 Micrel IN ...
Page 8
... MIC2025/2075 Current-Limit Response (Ramped Load Into Short—MIC2025-1) Short Removed Short-Circuit Current-Limit Current (650mA) Threshold (780mA) Thermal Shutdown TIME (100ms/div.) Current-Limit Transient Response (MIC2025-1) No Load Load 640mA Short-Circuit Current 24 s TIME (10 s/div.) MIC2025/2075 No Load (Output Reset by Removing Load—MIC2075-1) ...
Page 9
... C. The MIC2025 will automatically reset its output should the die temperature cool down to 120 C. The MIC2025 output and FLG signal will continue to cycle on and off until the device is disabled or the fault is removed. Figure 2 depicts typical timing. If the MIC2075 goes into thermal shutdown, its output will latch off and a pull-up current source is activated ...
Page 10
... See the Short-Circuit Transient Response graph under Functional Characteristics. Current-Limit Response—Ramped Load The MIC2025/75 current-limit profile exhibits a small foldback effect of about 200mA. Once this current-limit threshold is exceeded the device switches into a constant current mode important to note that the device will supply current until the current-limit threshold is exceeded ...
Page 11
... Printed Circuit Board Hot-Plug The MIC2025/75 are ideal inrush current-limiters suitable for hot-plug applications. Due to the integrated charge pump, the MIC2025/75 presents a high impedance when off and slowly becomes a low impedance as it turns on. This “soft- start” feature effectively isolates power supplies from highly capacitive loads by reducing inrush current during hot-plug events ...
Page 12
... Figure 5 USB Host Application 1.5k 3.3V MIC2025/75 USB Logic Controller VIN EN OUT ON/OFF OVERCURRENT FLG GND GND OUT 0.1µF NC Figure 6. USB Bus-Powered Hub 5.0V Ferrite Beads MIC2025/75 V BUS OUT D+ IN 0.01µF D– OUT 120µF GND NC 0.1µF Data Ferrite Beads V BUS D+ IN 120µF 0.01µF D– ...
Page 13
... SEATING PLANE 8-Lead SOP (M) 0.199 (5.05) 0.187 (4.74) 0.120 (3.05) 0.116 (2.95) 0.043 (1.09) 0.038 (0.97) 0.012 (0.30) R 0.008 (0.20) 5 MAX 0.004 (0.10) 0 MIN MM8™ 8-Pin MSOP (MM 0.010 (0.25) 0.007 (0.18) 0.050 (1.27) 0.016 (0.40) 0.244 (6.20) 0.228 (5.79) DIMENSIONS: INCH (MM) 0.007 (0.18) 0.005 (0.13) 0.012 (0.03) R 0.039 (0.99) 0.035 (0.89) 0.021 (0.53) Micrel MIC2025/2075 ...
Page 14
... MIC2025/2075 MIC2025/2075 14 Micrel March 2000 ...
Page 15
... MIC2025/2075 March 2000 15 Micrel MIC2025/2075 ...
Page 16
... This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. MIC2025/2075 + 1 (408) 944-0970 http://www ...