MIC2590B Micrel Semiconductor, MIC2590B Datasheet - Page 11

• Manufacturer Part Number: MIC2590B
• Description: Dual-Slot PCI Hot Plug Controller
• Manufacturer: Micrel Semiconductor

Functional Description
Hot Swap Insertion
When circuit boards are inserted into systems carrying live
supply voltages (“hot plugged”), high inrush currents often
result due to the charging of bulk capacitance that resides
across the circuit board’s supply pins. This transient inrush
current can cause the system’s supply voltages to tempo-
rarily go out of regulation, causing data loss or system lock-
up. In more extreme cases, the transients occurring during a
hot plug event may cause permanent damage to connectors
or on-board components.
The MIC2590B addresses these issues by limiting the inrush
currents to the load (PCI Board), and thereby controlling the
rate at which the load’s circuits turn on. In addition, the
MIC2590B offers input and output voltage supervisory func-
tions and current-limiting to provide robust protection for both
the host system and the PCI board.
System Interfaces
The MIC2590B employs two system interfaces. One is the
hot plug Interface (HPI) which includes ON[A/B], AUXEN[A/
B], and /FAULT[A/B]. The other is the System Management
Interface (SMI) consisting of SDA, SCL and /INT, (whose
signals conform to the specifications and format of Intel’s
SMBus standard). The MIC2590B can be operated exclu-
sively from the SMI, or can employ the HPI for power control
while continuing to use the SMI for access to all but the power
control registers.
In addition to the basic power control features of the MIC2590B
accessible by the HPI, the SMI also gives the host access to
the following information from the part:
1. Output voltage from each supply.
2. Output current from each supply.
3. Fault conditions occurring on each supply.
When using the System Management Interface for power
control, do not use the hot plug Interface. Conversely, when
using the HPI for power control, do not execute power control
commands over the SMI bus (all other register accesses via
the SMI bus remain permissible while in the HPI control
mode). Note that if power control is performed via the SMI
bus, the AUXENA, AUXENB, ONA and ONB pins should be
tied to ground.
Power-On Reset and Power Cycling
The MIC2590B utilizes VSTBY as the main supply input
source. It is required for proper operation of the MIC2590B
SMBus, registers and ADC and must be applied at all times.
A Power-On Reset (POR) cycle is initiated after VSTBY rises
above its UVLO threshold and remains valid at that voltage
for 500µs. All internal registers except RESULT are cleared
after POR. If VSTBY is recycled the MIC2590B enters a new
power-on reset cycle. VSTBY must be the first supply input
applied. Following the POR interval, the MAIN supply inputs
of 12V
The SMBus is ready for access at the end of the POR interval.
During t
August 2002
MIC2590B
IN
POR
, 12MV
all outputs are off.
IN
, 5V
IN
and 3V
IN
may be applied in any order.
11
Power-Up Cycle (See Typical Application Circuit)
When a slot is off, the 5VGATE and 3VGATE pins are held
low with an internal pull-down current source. When a slot’s
main outputs are enabled, and all input voltages are above
their respective undervoltage lockout thresholds, all four
main supplies execute a controlled turn on. At this time, the
GATE voltages of the 5V and 3.3V MOSFETs are ramped at
a controlled rate from 0V to approximately 11.5V. This is
sufficient to fully enhance the external MOSFETs for lowest
possible DC losses. The ramp rate is controlled by 25µA(typ.)
current sources from the GATE pins charging each C
The magnitude and slew rate of the output current is propor-
tional to the value of C
minimum value of C
start-up the load current does not exceed the current-limit
threshold. The following equation is used to determine the
value of C
Where C
and 5V outputs and I
current-limit and gate charge current specifications as given
in the Electrical Characteristics table. The output slew rate
dv/dt is computed by:
For the +12V and –12V supplies, the output slew rate is
controlled by capacitors connected to the 12VSLEWA and
12VSLEWB pins. To determine the minimum value of the
slew rate capacitor, (C
the following equation is used:
where C
and –12V outputs, and I
current-limit and slew rate charge current values found in the
Electrical Characteristics table. The equation above com-
putes the minimum value to guarantee the device does not
enter into current limit. The slew rate dv/dt is computed by:
By appropriate selection of the value of C
ensured that the magnitude of the inrush current never
exceeds the current limit for a given load capacitance. Since
Table 1. 3.3V/5V Output Slew Rate Selection
dv / dt (load)
C
dv / dt at load
SLEW
C
0.001µF
0.01µF
0.1µF
1µF
LOAD
LOAD
GATE
GATE
(min)
is the load capacitance connected to the +12V
is the load capacitance connected to the 3.3V
(min):
C
GATE
=
=
=
GATE
I
C
SLEW
I
I
C
(min)
SLEW
LIM
SLEW
GATE
LIM
GATE
SLEW
I
LIM
GATE
I
SLEW
is selected to ensure that during
and I
= 25
×
=
), connected to 12VSLEW[A/B],
×
and I
and the load capacitance. The
C
×
I
10
GATE
I
LOAD
10
LIM
µ
6
GATE
A
dv/dt (load)
25000V/s
2500V/s
250V/s
25V/s
6
SLEW
×
C
are respectively the
LOAD
are respectively the
SLEW
, it can be
MIC2590B
Micrel
GATE
.