MIC26950 MICREL, MIC26950 Datasheet - Page 16

• Manufacturer Part Number: MIC26950
• Description: 12A Hyper Speed Control Synchronous DC-DC Buck Regulator
• Manufacturer: MICREL

www.DataSheet4U.com
Micrel, Inc.
Application Information
Inductor Selection
Values for inductance, peak, and RMS currents are
required to select the output inductor. The input and
output voltages and the inductance value determine the
peak-to-peak inductor ripple current. Generally, higher
inductance values are used with higher input voltages.
Larger peak-to-peak ripple currents will increase the
power dissipation in the inductor and MOSFETs. Larger
output ripple currents will also require more output
capacitance to smooth out the larger ripple current.
Smaller peak-to-peak ripple currents require a larger
inductance value and therefore a larger and more
expensive inductor. A good compromise between size,
loss and cost is to set the inductor ripple current to be
equal to 20% of the maximum output current. The
inductance value is calculated by the Equation 4:
where:
f
20% = ratio of AC ripple current to DC output current
V
The peak-to-peak inductor current ripple is:
The peak inductor current is equal to the average output
current plus one half of the peak-to-peak inductor current
ripple.
The RMS inductor current is used to calculate the I
losses in the inductor.
SW
September 2010
IN(max)
= switching frequency, 300kHz
= maximum power stage input voltage
I
L
I
Δ
L(pk)
L(RMS)
I
=
L(pp)
V
=I
IN(max)
=
OUT(max)
V
=
OUT
V
OUT
I
×
OUT(max)
×
V
f
(V
sw
IN(max)
×
+ 0.5
IN(max)
(V
×
IN(max)
20%
2
×
×
+
f
−
sw
×
ΔI
ΔI
V
I
−
OUT(max)
×
OUT
L(pp)
V
L(PP)
12
L
OUT
)
2
)
(4)
(5)
(6)
(7)
2
R
16
Maximizing efficiency requires the proper selection of
core material and minimizing the winding resistance. The
high frequency operation of the MIC26950 requires the
use of ferrite materials for all but the most cost sensitive
applications. Lower cost iron powder cores may be used
but the increase in core loss will reduce the efficiency of
the power supply. This is especially noticeable at low
output power. The winding resistance decreases
efficiency at the higher output current levels. The
winding resistance must be minimized although this
usually comes at the expense of a larger inductor. The
power dissipated in the inductor is equal to the sum of
the core and copper losses. At higher output loads, the
core losses are usually insignificant and can be ignored.
At lower output currents, the core losses can be a
significant contributor. Core loss information is usually
available from the magnetics vendor. Copper loss in the
inductor is calculated by Equation 8:
The resistance of the copper wire, R
with the temperature. The value of the winding
resistance used should be at the operating temperature.
where:
T
T
R
(usually specified by the manufacturer)
Output Capacitor Selection
The type of the output capacitor is usually determined by
its ESR (equivalent series resistance). Voltage and RMS
current capability are two other important factors for
selecting the output capacitor. Recommended capacitor
types are tantalum, low-ESR aluminum electrolytic, OS-
CON and POSCAP. The output capacitor’s ESR is
usually the main cause of the output ripple. The output
capacitor ESR also affects the control loop from a
stability point of view. The maximum value of ESR is
calculated:
where:
ΔV
ΔI
H
20°C
WINDING(20°C)
L(PP)
OUT(pp)
= temperature of wire under full load
= ambient temperature
= peak-to-peak inductor current ripple
P
= peak-to-peak output voltage ripple
WINDING(Ht)
ESR
P
= room temperature winding resistance
INDUCTOR(Cu)
1 + 0.0042 × (T
C
OUT
= R
≤
WINDING(20°C)
ΔV
ΔI
= I
OUT(pp)
L(PP)
L(RMS)
H
– T
2
×
× R
20°C
WINDING
WINDING
))
M9999-091710-C
MIC26950
, increases
(10)
(8)
(9)