MIC5891 Micrel Semiconductor, MIC5891 Datasheet - Page 3

• Manufacturer Part Number: MIC5891
• Description: 8-Bit Serial-Input Latched Source Driver
• Manufacturer: Micrel Semiconductor

MIC5891
Timing Conditions
A.
B.
C.
D.
E.
F.
G.
H.
I.
Electrical Characteristics
V
Characteristic
Output Leakage Current
Output Saturation Voltage
Output Sustaining Voltage
Input Voltage
Input Current
Input Impedance
Maximum Clock Frequency
Serial Data Output Resistance
Turn-On Delay
Turnoff Delay
Supply Current
Diode Leakage Current
Diode Forward Voltage
BB
Note 4: Positive (negative) current is defined as going into (coming out of) the specified device pin.
Note 5: Operation of these devices with standard TTL may require the use of appropriate pull-up resistors.
Minimum data active time before clock pulse (data set-up time) ........................................................................75ns
Minimum data active time after clock pulse (data hold time) ..............................................................................75ns
Minimum data pulse width .................................................................................................................................150ns
Minimum clock pulse width ...............................................................................................................................150ns
Minimum time between clock activation and strobe ..........................................................................................300ns
Minimum strobe pulse width ..............................................................................................................................100ns
Typical time between strobe activation and output transition .............................................................................1.0 s
Turnoff delay ................................................................................................................ see Electrical Characteristics
Turn-on delay ............................................................................................................... see Electrical Characteristics
(V
= 50V, V
DD
= 5.0V, Logic Levels are V
DD
= 5V to 12V; T
A
= +25 C; unless noted.
Symbol
I
V
V
V
V
I
Z
f
R
t
t
I
I
I
V
DD
CEX
IN(1)
c
PLH
PHL
BB
DD
H
IN
CE(SAT)
CE(SUS)
IN(1)
IN(0)
F
OUT
and Ground)
V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
Max
Open
BB
Test Conditions
T
T
I
I
I
I
V
V
V
V
V
V
V
V
V
Output Enable to Output, I
Output Enable to Output, I
all outputs on, all outputs open
all outputs off
V
V
V
V
T
T
I
OUT
OUT
OUT
OUT
F
A
A
A
A
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
= 350mA
= +25 C
= +85 C
= +25 C
= +85 C
7-56
= 12V
= 5V to 12V
= 5.0V
= V
= 12V
= 5.0V
= 12V
= 5.0V
= 12V
= 5V, all outputs off, inputs = 0V
= 12V, all outputs off, inputs = 0V
= 5V, one output on, all inputs = 0V
= 12V, one output on, all inputs = 0V
= –100mA, T
= –225mA, T
= –350mA, T
= –350mA, L = 2mH
IN
= 5.0V
A
A
A
= +85 C
= +85 C
= +85 C
OUT
OUT
= –350mA
= –350mA
V
SS
Min.
10.5
100
3.5
3.3
35
50
–0.3
V
V
December 1997
Limits
DD
DD
Max.
–100
–50
240
200
100
200
100
1.8
1.9
2.0
0.8
6.0
2.0
1.0
3.0
2.0
50
20
10
10
50
+0.3
+0.3
Units
MHz
mA
mA
mA
k
k
k
k
Micrel
V
V
V
V
V
V
V
V
A
A
A
A
A
A
A
A
A
s
s