LM3509SDX National Semiconductor Corporation, LM3509SDX Datasheet
LM3509SDX
Related parts for LM3509SDX
LM3509SDX Summary of contents
Page 1
... The LM3509 is offered in a small 10-pin thermally- enhanced LLP package and operates over the -40°C to +85°C temperature range. Typical Application Circuits © 2007 National Semiconductor Corporation Features ■ Integrated OLED Display Power Supply and LED Driver ■ ...
Page 2
www.national.com 2 30004301 ...
Page 3
... Connection Diagram Ordering Information Order Number Package Type LM3509SD 10-Pin LLP LM3509SDX 10-Pin LLP Pin Descriptions/Functions Pin Name 1 MAIN Main Current Sink Input. 2 SUB/FB Secondary Current Sink Input or 1.25V Feedback Connection for Constant Voltage Output. 3 SET LED Current Setting Connection. Connect a resistor from SET to GND to set the maximum LED ...
Page 4
Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications OVP SUB/FB MAIN ...
Page 5
Symbol Parameter RESET/GPIO Pin Voltage Specifications V Input Logic Low IL V Input Logic High IH V Output Logic Low Compatible Voltage Specifications (SCL, SDA, VIO) V Serial Bus Voltage Level IO V Input Logic Low ...
Page 6
Typical Performance Characteristics Mode 2.2µF (OLED Mode), C OUT +25°C unless otherwise specified. SUB MAIN A 10 LED Efficiency Strings of 5LEDs) 6 LED Efficiency Strings ...
Page 7
OLED Efficiency vs I OUT 30004304 LED Line Regulation (UNI = '0') 30004359 OLED Line Regulation I = 60mA OLED 30004306 12V OLED Efficiency vs I OLED Line Regulation I = 60mA OLED OLED Load Regulation V = 18V ...
Page 8
OLED Load Regulation V = 12V OLED Over Voltage Limit vs. V Switching Frequency vs. V www.national.com Peak Current Limit vs. V 30004312 Switch On-Resistance vs 30004315 Maximum Duty Cycle vs 30004318 8 IN 30004314 IN ...
Page 9
Shutdown Current vs 30004320 LED Current Matching vs. CODE (Note 11) (UNI = '1 12kΩ -40°C to +85°C) SET A 30004322 LED Current vs CODE ( 12kΩ±0.05%) ...
Page 10
Start-Up Waveform (LED Mode) (2 × 5 LEDs, 30mA per string) Channel 1: SDA (5V/div) Channel 2: V (10V/div) OUT Channel 3: I (50mA/div) LED Channel 4: I (500mA/div) IN Time Base: 400µs/div Load Step (OLED Mode 18V, ...
Page 11
GPIO Functionality (GPIO Configured as OUTPUT, f Channel 2: GPIO (2V/div) Channel 3: SDA (2V/div) Channel 1:SCL (2V/div) Time Base: 40µs/div Ramp Rate Functionality (RMP1, RMP0 = '01') Channel 3: SDA (2V/div) Channel 1: I (10mA/div) MAIN Channel 4: I ...
Page 12
Block Diagram Operation Description The LM3509 Current Mode PWM boost converter operates from a 2.7V to 5.5V input and provides two regulated outputs for White LED and OLED display biasing. The first output, MAIN, provides a constant current of up ...
Page 13
In the instance when there are unequal numbers of LEDs or unequal currents from string to string, the string with the high- est voltage will be the regulation ...
Page 14
COMPATIBLE INTERFACE The LM3509 is controlled via an I START and STOP conditions classify the beginning and the end of the session. A START condition is defined as SDA transitioning from HIGH to LOW ...
Page 15
REGISTER DESCRIPTIONS There are 4, 8 bit registers within the LM3509 as detailed in Table 1. TABLE 1. LM3509 Register Descriptions Register Name General Purpose (GP) Brightness Main (BMAIN) Brightness Sub (BSUB) General Purpose I/O (GPIO) GENERAL PURPOSE REGISTER (GP) ...
Page 16
TABLE 3. Operational Truth Table UNI OLED ENM ENM ,ENS, or OLED high enables analog circuitry. BRIGHTNESS REGISTERS (BMAIN and BSUB) With the ...
Page 17
TABLE 4. I vs. Brightness Register Data LED BMAIN or BSUB Brightness Data 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 FIGURE ILED_MAX BMAIN or BSUB Brightness Data ...
Page 18
BRIGHTNESS RATE OF CHANGE DESCRIPTION RMP0 and RMP1 control the rate of change of the LED cur- rent I and I in response to changes in BMAIN and / MAIN SUB/FB or BSUB. There are 4 user programmable LED current ...
Page 19
Application Information LED CURRENT SETTING/MAXIMUM LED CURRENT Connect a resistor (R ) from SET to GND to program the SET maximum LED current (I ) into MAIN or SUB/FB. The LED_MAX relationship is: SET LED_MAX where SET ...
Page 20
TABLE 7. Recommended Output Capacitors Manufacturer Part Number TDK C1608X5R1E105M Murata GRM39X5R105K25D53 TDK C2012X5R1E225M Murata GRM219R61E225KA12 INDUCTOR SELECTION The LM3509 is designed for use with a 10µH inductor, how- ever 22µH are suitable providing the output capacitor is in- creased ...
Page 21
OUTPUT CURRENT RANGE (OLED MODE) The maximum output current the LM3509 can deliver in OLED mode is limited by 4 factors (assuming continuous conduc- tion); the peak current limit of 770mA (typical), the inductor value, the input voltage, and the ...
Page 22
Physical Dimensions www.national.com inches (millimeters) unless otherwise noted 10 Pin LLP For Ordering, Refer to Ordering Information Table NS Package Number SDA10A X1 = 3mm (±0.1mm 3mm (±0.1mm 0.8mm 22 ...
Page 23
Notes 23 www.national.com ...
Page 24
... National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. ...