LTC1264-7C Linear Technology, LTC1264-7C Datasheet
LTC1264-7C
Related parts for LTC1264-7C
LTC1264-7C Summary of contents
Page 1
... Bessel), while at three times the cutoff frequency the filter attains 55dB attenuation (vs 30dB for Bessel). The cutoff frequency of the LTC1264-7 is tuned via an external TTL or CMOS clock. The clock-to-cutoff frequency ratio of the LTC1264-7 can ...
Page 2
... CLK Phase Factor ( F ) Phase = 180 – (Note 1) Phase Nonlinearity (Note (Note 1) Operating Temperature Range LTC1264-7C ...................................... – LTC1264-7M ................................... – 125 C + Lead Temperature (Soldering, 10 sec)................. 300 0.3V ORDER PART NUMBER GND 3 ...
Page 3
... Note 1: Input frequencies, f, are linearly phase shifted through the filter as long cutoff frequency. C Figure 1 curve (A) shows the typical phase response of an LTC1264-7 operating 2.5MHz 100kHz. An endpoint straight line, curve (B), depicts the ideal linear CLK C phase response of the filter described by: phase shift = 180 – ...
Page 4
... LTC1264 TYPICAL PERFOR A Gain vs Frequency ±7. 1MHz CLK T = 25°C A –10 –20 –30 –40 50:1 25:1 –50 –60 –70 –80 –90 –100 1 10 100 1000 FREQUENCY (kHz) 1264-7 G01 Phase Factor vs f Max Representative Units) 450 V = ±7.5V S 445 ( 25:1 CLK ...
Page 5
... 1.5MHz 3 CLK T = 25° 2.0MHz CLK –1 – –3 –4 –5 10 100 FREQUENCY (kHz) LTC1264-7 Passband Gain vs f CLK ±7. 25 CLK –1 – 2 – 3 –4 –5 1000 ...
Page 6
... LTC1264 TYPICAL PERFOR A Gain vs f CLK 0.5MHz CLK 1MHz CLK 2MHz –10 CLK – –30 –40 –50 – SINGLE 5V S – 50:1 CLK C AGND = 2V – 25°C A –90 10 100 200 FREQUENCY (kHz) 1264-7 G17 Delay vs f CLK ...
Page 7
... Unit) CLK 0.000 180.00 25.000 71.77 50.000 – 37.11 75.000 – 146.19 100.000 – 255.85 LTC1264-7 Power Supply Current vs Power Supply Voltage 1MHz 44 CLK ...
Page 8
... LTC1264 TYPICAL PERFOR A Table 3. Passband Gain and Phase 25: CLK C A FREQUENCY (kHz) GAIN (dB 1MHz (Typical Unit) CLK 0.000 0.081 10.000 0.081 20.000 0.071 30.000 – 0.631 40.000 – 2.732 f = 2MHz (Typical Unit) CLK 0.000 – 0.016 20.000 – ...
Page 9
... CLK – gives a 50:1 ratio. For – 0 200 11 CLOCK SOURCE GND 8 DIGITAL SUPPLY V 1264-7 F02 OUT /f = 25:1 CLK CUTOFF 200 4 11 LTC1264-7 CLOCK SOURCE GND 7 8 DIGITAL SUPPLY OUT 1264-7 F03 /f = 25:1 CLK CUTOFF + 9 ...
Page 10
... Most of its frequency contents lie within the filter passband and it cannot be reduced with post filtering. For instance, the 50:1 LTC1264-7 wideband noise at 5V supply is 160 V 100 V RMS 145 V RMS ...
Page 11
... RMS IN CLK 0.7V (f 500kHz) If, for instance, an LTC1264-7 operating with a 100kHz RMS IN 0.5V (f 400kHz) RMS IN clock and 2kHz cutoff frequency receives a 95kHz 10mV input signal, a 5kHz 56 V output. When the LTC1264-7 operates with a clock-to- cutoff frequency of 25:1, aliasing occurs at twice the clock frequency ...
Page 12
... LTC1264-7 PACKAGE DESCRIPTIO 0.290 – 0.320 (7.366 – 8.128) 0.008 – 0.018 0° – 15° (0.203 – 0.460) 0.385 ± 0.025 0.038 – 0.068 (9.779 ± 0.635) (0.965 – 1.727) 0.300 – 0.325 (7.620 – 8.255) 0.015 (0.380) MIN 0.130 ± 0.005 (3.302 ± ...