LTC1569I Linear Technology, LTC1569I Datasheet
LTC1569I
Available stocks
Related parts for LTC1569I
LTC1569I Summary of contents
Page 1
... The LTC1569-7 is fully tested for a cutoff frequency of 256kHz/128kHz with single 5V/3V supply although up to 300kHz cutoff frequencies can be obtained. The LTC1569-7 features power savings modes and it is available in an SO-8 surface mount package. , LTC and LT are registered trademarks of Linear Technology Corporation. Frequency Response, f OUT R = 10k ...
Page 2
... XI U (Note 1) Total Supply Voltage ................................................ 11V Power Dissipation .............................................. 500mW Operating Temperature LTC1569C ............................................... LTC1569I ............................................ – Storage Temperature ............................ – 150 C Lead Temperature (Soldering, 10 sec).................. 300 C ELECTRICAL C HARA TERISTICS C The denotes the specifications which apply over the full operating temperature range, otherwise specifications are – ...
Page 3
ELECTRICAL C HARA TERISTICS C The denotes the specifications which apply over the full operating temperature range, otherwise specifications are – 3V 0V 4.096MHz CLK PARAMETER ...
Page 4
LTC1569 TYPICAL PERFOR A CE CHARACTERISTICS Gain vs Frequency 10 – 100 FREQUENCY (kHz) THD vs Input Frequency –68 – PIN –72 – 1.5V IN P-P f ...
Page 5
PIN FUNCTIONS + – IN /IN (Pins 1, 2): Signals can be applied to either or both input pins. The DC gain from IN (Pin 8) is 1.0, and the DC gain from Pin 2 to Pin ...
Page 6
LTC1569 APPLICATIONS INFORMATION Self-Clocking Operation The LTC1569-7 features a unique internal oscillator which sets the filter cutoff frequency using a single external resistor . The design is optimized for V 128kHz, where the filter cutoff frequency error is ...
Page 7
U U APPLICATIONS INFORMATION 1.010 1.008 1.006 V = 10V S 1.004 1.002 1.000 0.998 0.996 0.994 0.992 0.990 –50 – TEMPERATURE ( C) Figure 5. Filter Cutoff vs Temperature, ...
Page 8
LTC1569 APPLICATIONS INFORMATION The oscillator is sensitive to transients on the positive supply. The IC should be soldered to the PC board and the PCB layout should include ceramic capacitor be- + – tween V ...
Page 9
U U APPLICATIONS INFORMATION Table 2. Wideband Noise vs Supply Voltage, Single 3V Supply Bandwidth Total Integrated Noise CUTOFF • f CUTOFF CLK Table 3. Wideband Noise vs Supply Voltage, f ...
Page 10
LTC1569 APPLICATIONS INFORMATION every clock period. Therefore, the sampling frequency is twice the clock frequency and 64 times the filter cutoff frequency. Input signals with frequencies near 2 • will be aliased to the passband of ...
Page 11
... FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 12
... TA08 = 75/1 or 150/1, Very Low Noise = 50/1 or 100/ 100kHz CUTOFF(MAX) = 25/1, 50/1, 100/1 or 200/ 200kHz CUTOFF(MAX) = 25/ 200kHz, SO-8 CUTOFF(MAX) = 50/1 or 100/ 2.5mA 25/1 or 50/ 200kHz CUTOFF(MAX) = 150kHz (LTC1562) = 300kHz (LTC1562-2) 15697f LT/TP 0300 4K • PRINTED IN THE USA LINEAR TECHNOLOGY CORPORATION 1998 = 8.56k + 1569-7 TA10 ...