LTC3407A-2 Linear Technology, LTC3407A-2 Datasheet - Page 7

• Manufacturer Part Number: LTC3407A-2
• Description: Dual Synchronous 800mA2.25MHz Step-Down DC/DC Regulator
• Manufacturer: Linear Technology

The LTC3407A-2 uses a constant frequency, current mode
architecture. The operating frequency is set at 2.25MHz
and can be synchronized to an external oscillator. Both
channels share the same clock and run in-phase. To suit
a variety of applications, the selectable MODE/SYNC pin
allows the user to trade-off noise for efficiency.
The output voltage is set by an external divider returned to
the V
output voltage with a reference voltage of 0.6V and adjusts
the peak inductor current accordingly. Overvoltage and
undervoltage comparators will pull the POR output low if
the output voltage is not within ±8.5%. The POR output
will go high after 65,536 clock cycles (about 29ms in pulse
skipping mode) of achieving regulation.
Main Control Loop
During normal operation, the top power switch (P-channel
MOSFET) is turned on at the beginning of a clock cycle
when the V
current into the inductor and the load increases until the
current limit is reached. The switch turns off and energy
stored in the inductor flows through the bottom switch (N-
channel MOSFET) into the load until the next clock cycle.
The peak inductor current is controlled by the internally
compensated I
amplifier.This amplifier compares the V
reference. When the load current increases, the V
age decreases slightly below the reference. This
decrease causes the error amplifier to increase the I
voltage until the average inductor current matches the new
load current.
The main control loop is shut down by pulling the RUN/SS
pin to ground.
Low Current Operation
Two modes are available to control the operation of the
LTC3407A-2 at low currents. Both modes automatically
switch from continuous operation to the selected mode
when the load current is low.
To optimize efficiency, the Burst Mode operation can be
selected. When the load is relatively light, the LTC3407A-2
OPERATIO
FB
pins. An error amplifier compares the divided
FB
voltage is below the reference voltage. The
TH
voltage, which is the output of the error
U
FB
pin to the 0.6V
FB
volt-
TH
automatically switches into Burst Mode operation in which
the PMOS switch operates intermittently based on load
demand with a fixed peak inductor current. By running
cycles periodically, the switching losses which are domi-
nated by the gate charge losses of the power MOSFETs are
minimized. The main control loop is interrupted when the
output voltage reaches the desired regulated value. A
voltage comparator trips when I
ting off the switch and reducing the power. The output
capacitor and the inductor supply the power to the load
until I
control loop which starts another cycle.
For lower ripple noise at low currents, the pulse skipping
mode can be used. In this mode, the LTC3407A-2 contin-
ues to switch at a constant frequency down to very low
currents, where it will begin skipping pulses.
Dropout Operation
When the input supply voltage decreases toward the
output voltage, the duty cycle increases to 100% which is
the dropout condition. In dropout, the PMOS switch is
turned on continuously with the output voltage being
equal to the input voltage minus the voltage drops across
the internal P-channel MOSFET and the inductor.
An important design consideration is that the R
the P-channel switch increases with decreasing input
supply voltage (See Typical Performance Characteristics).
Therefore, the user should calculate the power dissipation
when the LTC3407A-2 is used at 100% duty cycle with low
input voltage (See Thermal Considerations in the Applica-
tions Information Section).
Low Supply Operation
The LTC3407A-2 incorporates an undervoltage lockout
circuit which shuts down the part when the input voltage
drops below about 1.65V to prevent unstable operation.
A general LTC3407A-2 application circuit is shown in
Figure 1. External component selection is driven by the
load requirement, and begins with the selection of the
inductor L. Once the inductor is chosen, C
be selected.
TH
exceeds 0.65V, turning on the switch and the main
LTC3407A-2
TH
www.DataSheet4U.com
is below 0.65V, shut-
IN
and C
DS(ON)
OUT
3407a2f
7
can
of