LTC3858-1 Linear Technology Corporation, LTC3858-1 Datasheet - Page 17

• Manufacturer Part Number: LTC3858-1
• Description: Dual 2-Phase Synchronous Step-Down Controller
• Manufacturer: Linear Technology Corporation

www.DataSheet4U.com
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
Ensure that R1 has a power rating higher than this value.
If high effi ciency is necessary at light loads, consider this
power loss when deciding to use inductor DCR sensing
or sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor, due
to the extra switching losses incurred through R1. However,
DCR sensing eliminates a sense resistor, reduces conduc-
tion losses and provides higher effi ciency at heavy loads.
Peak effi ciency is about the same with either method.
Inductor Value Calculation
The operating frequency and inductor selection are inter-
related in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components? The answer is effi ciency. A higher
frequency generally results in lower effi ciency because
of MOSFET gate charge losses. In addition to this basic
trade-off, the effect of inductor value on ripple current and
low current operation must also be considered.
The inductor value has a direct effect on ripple current.
The inductor ripple current ΔI
inductance or higher frequency and increases with higher
V
Accepting larger values of ΔI
inductances, but results in higher output voltage ripple
and greater core losses. A reasonable starting point for
setting ripple current is ΔI
ΔI
The inductor value also has secondary effects. The tran-
sition to Burst Mode operation begins when the average
inductor current required results in a peak current below
APPLICATIONS INFORMATION
IN
L
P
ΔI
:
LOSS
occurs at the maximum input voltage.
L
=
( )( )
R
f L
1
1
=
(
V
V
IN MAX
OUT
(
⎛
⎝ ⎜
1–
)
–
R
V
L
V
V
OUT
1
OUT
= 0.3(I
IN
L
L
⎞
⎠ ⎟
)
allows the use of low
decreases with higher
•
V
MAX
OUT
). The maximum
30% of the current limit determined by R
inductor values (higher ΔI
lower load currents, which can cause a dip in effi ciency in
the upper range of low current operation. In Burst Mode
operation, lower inductance values will cause the burst
frequency to decrease.
Inductor Core Selection
Once the value for L is known, the type of inductor must
be selected. High effi ciency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite or molypermalloy
cores. Actual core loss is independent of core size for a
fi xed inductor value, but it is very dependent on inductance
value selected. As inductance increases, core losses go
down. Unfortunately, increased inductance requires more
turns of wire and therefore copper losses will increase.
Ferrite designs have very low core loss and are preferred
for high switching frequencies, so design goals can con-
centrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that induc-
tance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Power MOSFET and Schottky Diode
(Optional) Selection
Two external power MOSFETs must be selected for each
controller in the LTC3858-1: one N-channel MOSFET for
the top (main) switch, and one N-channel MOSFET for the
bottom (synchronous) switch.
The peak-to-peak drive levels are set by the INTV
This voltage is typically 5.1V during start-up (see EXTV
Pin Connection). Consequently, logic-level threshold
MOSFETs must be used in most applications. The only
exception is if low input voltage is expected (V
then, sub-logic level threshold MOSFETs (V
should be used. Pay close attention to the BV
fi cation for the MOSFETs as well; many of the logic-level
MOSFETs are limited to 30V or less.
L
) will cause this to occur at
LTC3858-1
SENSE
GS(TH)
CC
DSS
IN
. Lower
voltage.
17
< 4V);
speci-
< 3V)
38581f
CC