LTC4416-1 Linear Technology, LTC4416-1 Datasheet
LTC4416-1
Related parts for LTC4416-1
LTC4416-1 Summary of contents
Page 1
... The LTC4416 “fast off” feature is engaged when the sense voltage exceeds the input voltage by 25mV. The LTC4416-1 enables the fast off under the same conditions and when the other external P-channel device is selected using the enable pins ...
Page 2
... LTC4416/LTC4416-1 ABSOLUTE AXI U RATI (Note 1) Supply Voltage (V1, V2) .............................. –14V to 40V Voltage from ....................... –40V to 40V S Input Voltage E1, E2 .................................................... –0.3V to 40V V ........................................................... –14V to 40V S Output Voltage G1 ....... –0.3V to the Higher 0. ....... –0.3V to the Higher 0. H1, H2 ..................................................... –0. Operating Ambient Temperature Range (Note 2) LTC4416E ............................................ – ...
Page 3
... V – < –6V 17nF (Note > –1.5V 17nF (Note (Note 14) LTC4416-1 Only 3.6V ≤ ≤ 36V (Note 10 3.6V ≤ ≤ 36V (Note 10 (Note 11) (Note 11) 3.6V ≤ ≤ 36V, –40°C to 85° ≤ ...
Page 4
... LTC4416/LTC4416-1 TYPICAL PERFOR A CE CHARACTERISTICS Temperature and Supply FR Voltage 40 35 –40°C 27°C 30 125° SUPPLY VOLTAGE (V) 4416 G01 V1, V2 and V Pin Leakage vs S Temperature –0.25 –0. – 28V – 28V – ...
Page 5
... If the E1 signal is driven low, the V1 path will perform a “soft-off” provided the PFET(s) are properly configured for blocking DC current. An internal current sink will pull the E1 pin down when the E1 input exceeds 1.5V. E1 (Pin 2): LTC4416-1 Comparator Enable Input. A high signal greater than V will enable the V1 path. The ideal REF diode action will then determine if the V1 path should turn on by controlling any PFET(s) connected to the G1 pin ...
Page 6
... OPERATIO U Operation can best be understood by referring to the Block Diagram which illustrates the internal circuit blocks. The LTC4416/LTC4416-1 are divided into three sections, namely: 1. The channel 1 controller consisting of A1, C1, the “first analog contoller,” the G1 drivers and the H1 output driver. 2. The band-gap reference 3. The channel 2 controller consisting of A2, C2, the “ ...
Page 7
... This means that G2 will only provide an I current instead of either an I G(SRC) current. 4416 F01 When V E2 enabled, and G2 will become active implementing the I – output current listed in Figure 1. LTC4416/LTC4416-1 www.DataSheet4U.com FR – When GFON(SNK) E2 Operation Mode I ...
Page 8
... GFON(SNK) LTC4416-1 OPERATION The LTC4416-1 is designed for overvoltage/undervoltage protection or when either voltage path must be turned off rapidly, regardless of the status of the other voltage input. The LTC4416-1 does not implement the soft-off feature < channel 2 VS RTO implemented in the LTC4416. The E1 and E2 inactive will force the I Table 2 explains the operation of the E1 and E2 inputs ...
Page 9
... In this case the LTC4416 acts S as two interconnected ideal diode controllers. V supplied by the higher of the two supplies, V1 and V2 and V2 are exactly the same, then 50% of the current for V will be supplied by each supply. As the two supplies S LTC4416/LTC4416-1 www.DataSheet4U.com SUP75P03_07 PRIMARY SUPPLY Q1 R1A 221k LTC4416 ...
Page 10
... Figure 5. Dual PowerPath for Current Sharing LTC4416-1 The LTC4416-1 will support all three of the LTC4416 applications without the “soft-off” feature. The only dif- ference in the two designs is the LTC4416-1 will rapidly switch off the load from a supply whenever a channel disabled ...
Page 11
... Figure 8. Transient Response of the LTC4416 vs the LTC4416-1 Light Load with a Large Capacitor OUT TO LOAD 4416 F07 Figure 9. Close Up of the Transient Response of the LTC4416 Rapidly Rising Input LTC4416/LTC4416-1 www.DataSheet4U.com time prior to the rapid pull- E(OFF) which has a minimum current of 500µA. G(OFF) = ...
Page 12
... LTC4416/LTC4416-1 PACKAGE DESCRIPTIO 0.889 ± 0.127 (.035 ± .005) GAUGE PLANE 5.23 3.20 – 3.45 (.206) (.126 – .136) MIN 0.18 0.305 ± 0.038 0.50 (.007) (.0120 ± .0015) (.0197) BSc TYP REcOMMENDED SOLDER PAD LAYOUT NOTE: 1. DIMENSIONS IN MILLIMETER/(INcH) 2. DRAWING NOT TO ScALE 3. DIMENSION DOES NOT INcLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. ...