MX25L1605 Macronix International, MX25L1605 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
MX25L1605
Manufacturer Part Number
MX25L1605
Description
16M-BIT [x 1] CMOS SERIAL FLASH
Manufacturer
Macronix International
Datasheet
1.MX25L1605.pdf
(45 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MX25L1605AM21-15G
Manufacturer:
MXIC
Quantity:
1 700
Company:
Part Number:
MX25L1605AM2C-12G
Manufacturer:
MXIC
Quantity:
126
Company:
Part Number:
MX25L1605AM2C-15G
Manufacturer:
SAM
Quantity:
3 000
Part Number:
MX25L1605AM2C-15G
Manufacturer:
MXIC/旺宏
Quantity:
20 000
Company:
Part Number:
MX25L1605AM2I-15G
Manufacturer:
MXIC
Quantity:
1 700
Part Number:
MX25L1605AM2I-15G
Manufacturer:
MXIC/旺宏
Quantity:
20 000
Part Number:
MX25L1605AMC-15G
Manufacturer:
MXIC/旺宏
Quantity:
20 000
Part Number:
MX25L1605DM1I-12G
Manufacturer:
MXIC/旺宏
Quantity:
20 000
Part Number:
MX25L1605DM21-12G
Manufacturer:
MXIC/旺宏
Quantity:
20 000
www.DataSheet4U.com
(4) Read Status Register (RDSR)
The RDSR instruction is for reading Status Register Bits. The Read Status Register can be read at any time (even in
program/erase/write status register condition) and continuously. It is recommended to check the Write in Progress (WIP)
bit before sending a new instruction when a program, erase, or write status register operation is in progress.
The sequence of issuing RDSR instruction is: CS# goes low-> sending RDSR instruction code-> Status Register data out
on SO (see Figure. 15)
The definition of the status register bits is as below:
WIP bit. The Write in Progress (WIP) bit, a volatile bit, indicates whether the device is busy in program/erase/write status
register progress. When WIP bit sets to 1, which means the device is busy in program/erase/write status register progress.
When WIP bit sets to 0, which means the device is not in progress of program/erase/write status register cycle.
WEL bit. The Write Enable Latch (WEL) bit, a volatile bit, indicates whether the device is set to internal write enable latch.
When WEL bit sets to 1, which means the internal write enable latch is set, the device can accept program/erase/write
status register instruction. When WEL bit sets to 0, which means no internal write enable latch; the device will not accept
program/erase/write status register instruction.
BP2, BP1, BP0 bits. The Block Protect (BP2, BP1, BP0) bits, non-volatile bits, indicate the protected area(as defined
in table 1) of the device to against the program/erase instruction without hardware protection mode being set. To write the
Block Protect (BP2, BP1, BP0) bits requires the Write Status Register (WRSR) instruction to be executed. Those bits
define the protected area of the memory to against Page Program (PP), Sector Erase (SE), and Chip Erase(CE) instructions
(only if all Block Protect bits set to 0, the CE instruction can be executed)
Program/erase error bit. When the program/erase bit set to 1, there is an error occurred in last program/erase operation.
The Flash may accept a new program/erase command to re-do program/erase operation.
SRWD bit. The Status Register Write Disable (SRWD) bit, non-volatile bit, is operated together with Write Protection (WP#)
pin for providing hardware protection mode. The hardware protection mode requires SRWD sets to 1 and WP# pin signal
is low stage. In the hardware protection mode, the Write Status Register (WRSR) instruction is no longer accepted for
execution and the SRWD bit and Block Protect bits (BP2, BP1, BP0) are read only.
Note: 1. See the table "Protected Area Sizes".
P/N: PM1168
Register Write
register write
1= status
Protect
disable
SRWD
Status
bit 7
Program/
1=error
erase
bit 6
error
bit 5
0
the level of the level of the level of
protected
(note 1)
block
bit 4
BP2
protected
(note 1)
11
block
bit 3
BP1
protected
(note 1)
block
bit 2
BP0
MX25L1605
1=write enable 1=write operation
(write enable
0=not write
enable
latch)
WEL
bit 1
(write in progress
REV. 1.3, NOV. 06, 2006
0=not in write
operation
bit 0
WIP
bit)