mtd4n20e Freescale Semiconductor, Inc, mtd4n20e Datasheet
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mtd4n20e
Available stocks
Related parts for mtd4n20e
mtd4n20e Summary of contents
Page 1
... Preferred devices are Motorola recommended choices for future use and best overall value. REV 1 Motorola TMOS Power MOSFET Transistor Device Data Motorola, Inc. 1995 D G Rating 10 ms) Order this document by MTD4N20E/D MTD4N20E Motorola Preferred Device TMOS POWER FET 4.0 AMPERES 200 VOLTS R DS(on) = 1.2 OHM CASE 369A–13, Style 2 ...
Page 2
... MTD4N20E ELECTRICAL CHARACTERISTICS ( 25°C unless otherwise noted) Characteristic OFF CHARACTERISTICS Drain–Source Breakdown Voltage ( Vdc 0.25 Adc) Temperature Coefficient (Positive) Zero Gate Voltage Drain Current ( 200 Vdc Vdc 200 Vdc Vdc 125°C) Gate–Body Leakage Current ( ± 20 Vdc ...
Page 3
... Figure 4. On–Resistance versus Drain Current 100 100 125 150 DRAIN–TO–SOURCE VOLTAGE (VOLTS) Figure 6. Drain–To–Source Leakage MTD4N20E – 55°C 25°C 100° ...
Page 4
... MTD4N20E Switching behavior is most easily modeled and predicted by recognizing that the power MOSFET is charge controlled. The lengths of various switching intervals ( t) are deter- mined by how fast the FET input capacitance can be charged by current from the generator. The published capacitance data is difficult to use for calculat- ing rise and fall because drain– ...
Page 5
... DM ), the energy rating is specified at rated continuous current ( accordance with industry custom. The energy rating must be derated for temperature as shown in the accompanying graph (Figure 12). Maximum energy at currents below rated continuous I D can safely be assumed to equal the values indicated. MTD4N20E t d(off) t d(on GATE RESISTANCE (OHMS) 0 ...
Page 6
... MTD4N20E 100 SINGLE PULSE 25°C 10 1.0 0.1 R DS(on) LIMIT THERMAL LIMIT PACKAGE LIMIT 0.01 0.1 1 DRAIN–TO–SOURCE VOLTAGE (VOLTS) Figure 11. Maximum Rated Forward Biased Safe Operating Area 1 0.5 0.2 0.1 0.05 0.1 0.02 0.01 SINGLE PULSE 0.01 1.0E–05 1.0E–04 Figure 14. Diode Reverse Recovery Waveform 6 SAFE OPERATING AREA 80 60 ...
Page 7
... Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. MTD4N20E Board Material = 0.0625″ G–10/FR– Copper 25°C 5.0 Watts ...
Page 8
... MTD4N20E Prior to placing surface mount components onto a printed circuit board, solder paste must be applied to the pads. Solder stencils are used to screen the optimum amount. These stencils are typically 0.008 inches thick and may be made of brass or stainless steel. For packages such as the SC–59, SC– ...
Page 9
... SOLDER IS LIQUID FOR SECONDS 100°C 140°C (DEPENDING ON MASS OF ASSEMBLY) DESIRED CURVE FOR LOW MASS ASSEMBLIES Figure 17. Typical Solder Heating Profile MTD4N20E STEP 6 STEP 7 VENT COOLING 205° TO 219°C PEAK AT SOLDER JOINT T MAX 9 ...
Page 10
... D 0.027 0.035 0.69 0.88 E 0.033 0.040 0.84 1.01 F 0.037 0.047 0.94 1.19 G 0.180 BSC 4.58 BSC H 0.034 0.040 0.87 1.01 J 0.018 0.023 0.46 0.58 K 0.102 0.114 2.60 2.89 L 0.090 BSC 2.29 BSC R 0.175 0.215 4.45 5.46 S 0.020 0.050 0.51 1.27 U 0.020 ––– 0.51 ––– V 0.030 0.050 0.77 1.27 Z 0.138 ––– 3.51 ––– MTD4N20E/D ...