RS5-R30/RD30
3.0 Watt 2:1 regulated
single & dual output
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation
Load regulation
Cross regulation (dual output)
Ripple & Noise
Short circuit protection
Temperature coefficient
Capacitor load
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current
GENERAL SPECIFICATIONS
Efficiency
I/O isolation voltage
I/O isolation capacitance
I/O isolation resistance
Switching frequency
Humidity
Reliability calculated MTBF
Safety standard
PHYSICAL SPECIFICATIONS
Case material
Pin material
Potting material
Weight
Dimensions
ENVIRONMENT SPECIFICATIONS
Operating temperature
Maximum case temperature
Storage temperature
Cooling
EMI CHARACTERISTICS
Conducted Emissions
Radiated Emissions
ESD
RS
EFT
Surge
CS
PFMF
(11)
(11)
(20 MHz bandwith) (1)
(2)
(designed to meet)
(From 25% to 100% Load)
(3 sec.)
(min.)
(10)
(min.)
Input / Output
Indefinite (automatic recovery)
(3)
Non-conductive black plastic
EN55022
EN55022
IEC61000-4-2 Perf.Criteria B
IEC61000-4-3 Perf.Criteria A
IEC61000-4-4 Perf.Criteria B
IEC61000-4-5 Perf.Criteria B
IEC61000-4-6 Perf.Criteria A
IEC61000-4-8 Perf.Criteria A
SIP > 0.86“ x 0.36“ x 0.44“
C5191R-H solder-coated
> 2.465 Mhrs. @25°C
Epoxy (UL94V-0 rated)
Nature convection
± 1%
± 5%
± 0.02%/°C
1600 VDC
680 pF max.
-40°C~ 71°C
100°C
± 0.5%
± 1%
75 mV pk-pk
See table
See table
See table
See table
Capacitors
35 mA pk-pk
See table
1000 M Ohm
100 kHz
95% rel. H
IEC 60950
4.8 g, typ.
-40°C~125°C
CLASS A
CLASS A
■
■
■
■
■
■
■
ABSOLUTE MAXIMUM RATINGS
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
Lead soldering temperature
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
NOTE
1) Ripple / Noise measured with 20 MHz bandwith.
2) Tested by minimal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH and source capacitor Cin (47uF,
ESR < 1.0 Ohm @100 kHz).
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation at no-load conditions will not damage these
devices. However they may not meet all listed
specifications.
Input filter components are required to help meet Conducted Emission
class A, which application refer to the EMI filter of design & feature
configuration.
An external filter capacitor is required if the module has to meet EN61000-
4-4 and EN61000-4-5.
8 Pin SIL package
Wide 2:1 input range
1600 VDC isolation
Continuous short circuit protection
Efficiency up to 84%
-40°C~71°C operation temperature range
Metal case, Remote On/Off optional
Transient Recovery Time 300 us typ., Transient Response
Deviation ± 3% max., Test by normal Vin and 100% -
25% load, 25% load step change.
Remote ON / OFF control
ON: open or high impedance
OFF: 3.0~6.0 mA input current (via 1K)
5 modes
12 modes
24 modes
48 modes (SIP)
(1.5 mm from case 10 sec.)
-0.7 ~ 15 VDC
-0.7 ~ 36 VDC
-0.7 ~ 50 VDC
-0.7 ~ 100 VDC
260°C
Page: 1/4
Last update: 30.01.09
(4)