si4710-b30 Silicon Laboratories, si4710-b30 Datasheet - Page 20
![no-image](/images/no-image-200.jpg)
si4710-b30
Manufacturer Part Number
si4710-b30
Description
Si4710/11-b30 Fm Radio Transmitter
Manufacturer
Silicon Laboratories
Datasheet
1.SI4710-B30.pdf
(40 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
si4710-b30-GMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Si4710/11-B30
(LIN/RIN) with programmable attenuation. To ensure
optimal audio performance, the Si4710/11 has a
transmit line input property that allows the user to
specify the peak amplitude of the analog input required
to reach maximum deviation level. The deviation levels
of the audio, pilot, and RDS/RBDS signals can be
independently programmed to customize FM transmitter
designs. The Si4710/11 has a programmable low audio
level and high audio level indicators that allows the user
to selectively enable and disable the carrier based on
the presence of audio content. In addition, the device
provides an overmodulation indicator to allow the user
to dynamically set the maximum deviation level. The
Si4710/11 has a programmable audio dynamic range
control that can be used to reduce the dynamic range of
the audio input signal and increase the volume at the
receiver. These features can dramatically improve the
end user’s listening experience.
The Si4710/11 is reset by applying a logic low on the
RST pin. This causes all register values to be reset to
their default values. The digital input/output interface
supply (V
RCLK, DIN, DFS, and DCLK pins and can be connected
to the audio baseband processor's supply voltage to
save power and remove the need for voltage level
translators. RCLK is not required for register operation.
The Si4710/11 reference clock is programmable,
supporting many RCLK inputs as shown in Table 9.
The Si4710/11 are part of a family of broadcast audio
solutions offered in standard, 3 x 3 mm 20-pin QFN
packages. All solutions are layout compatible, allowing
a single PCB to accommodate various feature offerings.
The Si4710/11 includes line inputs to the on-chip
analog-to-digital converters (ADC), a programmable
reference clock input, and a configurable digital audio
interface. The chip supports I
SPI, and a 3-wire control interface.
20
IO
) provides voltage to the RST, SEN, SDIO,
2
C-compliant 2-wire, 8-bit
Rev. 1.1
5.2. FM Transmitter
The transmitter (TX) integrates a stereo audio ADC to
convert analog audio signals to high fidelity digital
signals. Alternatively, digital audio signals can be
applied to the Si4710/11 directly to reduce power
consumption by eliminating the need to convert audio
baseband signals to analog and back again to digital.
Digital signal processing is used to perform the stereo
MPX encoding and FM modulation to a low digital IF.
Transmit baseband filters suppress out-of-channel
noise and images from the digital low-IF signal. A
quadrature single-sideband mixer up-converts the
digital IF signal to RF, and internal RF filters suppress
noise and harmonics to support the harmonic emission
requirements of cellular phones, GPS, WLAN, and other
wireless standards.
The TXO output has over 10 dB of output level control,
programmable in approximately 1 dB steps. This large
output range enables a variety of antennas to be used
for transmit, such as a monopole stub antenna or a loop
antenna. The 1 dB step size provides fine adjustment of
the output voltage.
The TXO output requires only one external 120 nH
inductor. The inductor is used to resonate the antenna
and is automatically calibrated within the integrated
circuit to provide the optimum output level and
frequency response for supported transmit frequencies.
Users are responsible for adjusting their system’s
radiated power levels to comply with local regulations
on RF transmission (FCC, ETSI, ARIB, etc.).