S10227 Hamamatsu Photonics, K.K.,, S10227 Datasheet - Page 4

no-image

S10227

Manufacturer Part Number
S10227
Description
Cmos Linear Image Sensor
Manufacturer
Hamamatsu Photonics, K.K.,
Datasheet
4
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741
(1) Electrostatic countermeasures
(2) Package handling
(3) Reflow soldering
(4) Surface protective tape
Recommended land pattern
Precautions for use
Pin connection
· This device has a built-in protection circuit as a safeguard against static electrical charges. However, to prevent destroying
· Protect this device from surge voltages which might be caused by peripheral equipment.
· The package surface is easily scratched, so handle this device carefully.
· Dust or grime on the light input window might cause non-uniform sensitivity. To remove dust or grime, blow it off with
· To prevent damaging this device during reflow soldering, perform soldering within 24 hours after opening the moisture-proof
· The extent of damage that might occur during reflow soldering depends on the PC board size and reflow oven conditions.
· Protective tape is affixed to the surface of this product to protect the active area. After assembling the product, remove the
Pin No.
the device with electrostatic charges, take countermeasures such as grounding yourself, the workbench and tools to prevent
static discharges.
compressed air.
packing.
Check the device for any damage before reflow soldering.
tape before use.
2.54
2.54
(8 ×)
Name
Video
GND
EOS
CLK
Vdd
0.7
NC
NC
ST
2.54
Ground
Power supply voltage
Video signal output
End of scan (Shift register end-of-scan signal pulse generated after reading
signals from all pixels)
Start pulse (Pulse for initializing the internally generated pulses that set the
timing to start reading pixel signals)
Clock pulse (Pulse for synchronizing the internally generated pulses that
control sensor operation frequency)
KMPDC0257EA
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions.
Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2008 Hamamatsu Photonics K.K.
Temperature profile of reflow soldering
250
200
150
100
50
0
0
50
Description
100
CMOS linear image sensor
150
TIME (s)
200
250
300
350
KMPDB0261EA
S10227
Input/output
Output
Output
Input
Input
Input
Input
Cat. No. KMPD1099E04
Nov. 2008 DN
-
-

Related parts for S10227